background image

 

1.0 Introduction 

The  PAC-3P  is  a  portable,  battery  powered  3  phase  stand-alone  test  instrument  for 
performing  earth  continuity  and  earth  leakage  current  tests  as  required  by  AS/NZS  3760, 
including: 

Earth continuity @ 200mA 
Leakage Current Test – Mains-powered 

The unit conducts a sequence test, starting with an earth continuity test and then proceeding 
with the leakage test. It indicates Pass/Fail and the actual measured readings on the LCD 
display and provides on-screen user prompts. It includes safety features such as preventing 
a leakage current test in event of a failed earth continuity test result. 20A and 32A extension 
lead test adaptor  is  included  with  an  earth test pin  terminal,  which eliminates  the need for 
probing of the extension lead earth. 

 

2.0 PAC-3P Specifications 

Display LCD 
Indication PASS/FAIL and measured values 
Operation 2 push buttons 

Earth Continuity Test: 
Display Range 
0.1ohm to 20ohm 
Test Current 200mA 
Pass/Fail Limit 1ohm 
Accuracy better than 5% at 1ohm 

Leakage Test: 
Display Range 
0.15mA to 9.99mA 
Pass/Fail Limit 5mA 
Accuracy better than 5% at 5mA 

Power Source 2x9V batteries 
Accessory 20A and 32A extension lead test adaptor with earth test pin 

 

3.0 User Note 

This instrument and its operating instructions are intended for use by adequately 
trained personnel who are AS3760 competent. 

It is important to follow the documentation and operating instructions to avoid danger. 

 

 

Summary of Contents for ProTag PAC-3P

















Reviews: