background image

33

buttons will always have priority over the commands received 

from the telephone interface.

If you press the ‘     ’ or ‘     ’ button on the chronostat, the device 

will change its status and the ‘        ’ icon will flash to indicate that 

the interface command has been overridden by a command input with 

a control button.

The ‘      ’ icon will stop flashing if the telephone interface sends the 

chronostat the same command as the one made with the button or 

if the telephone interface is reset. In such a case the status set by 

means of the control button will not be changed and the chronostat 

will be ready to receive a new command.

IMPORTANT

If an Off command is sent to the chronostat via the telephone 

interface  (contact  open),  it  is  a  good  idea  to  check  that  the 

command has been executed by the chronostat by carrying out 

the following realignment procedure:

1. Using the functions of the telephone interface, check that the 

contact is open, sending an Off command if necessary.

2. Send  a  command  to  the  telephone  interface  to  close  the 

contact (the chronostat will turn on).

3. Using the functions of the telephone interface, check that the 

contact is closed.

4. Send  a  command  to  the  telephone  interface  to  open  the 

contact (the chronostat will turn off).

During  this  sequence  no  commands  should  be  input  with 

the  control  buttons  as  they  have  priority  over  the  interface 

commands.

TECHNICAL CHARACTERISTICS 

Power supply:     

2 x 1.5V, alkaline batteries (Type AA)

Battery life: 

   

> 2,5 years

Frequency:   

 

868,150 MHz

Modulation:   

 

GFSK

Effective radiated power (ERP): < 1 mW

Antenna type: 

 

Internal

Max. receiver distance: 

>300 m in free air

 

 

 

>50  m  in  buildings  (depending  on 

the building and environment)

Room temperature

Regulation range:

 

comfort: 

5,0 .. 35,0°C

 

economy: 

5,0 .. 35,0°C

Hysteresis:   

 

0,2°C adjustable 0,1 .. 5,0 °C

Sensor type:  

 

NTC 4K7 ohm ±1% @ 25°C

Resolution:   

 

0,1°C  (T > 0,0°C)

 

 

 

0,2°C  (T < 0,0°C)

Range: 

 

 

-9,9°C .. +50,0°C

Precision:   

 

±1,0°C

Floor temperature (external sensor)

Regulation range:   

Lower limit: 10 .. 30°C

 

 

 

Upper limit: 35°C .. 50°C

Sensor type:  

 

NTC 4K7 ohm ±1% @ 25°C

Resolution:   

 

0,1°C  (T > 0,0°C)

 

 

 

0,2°C  (T < 0,0°C)

- ENGLISH -

Summary of Contents for N CTA W




















Reviews: