background image

7

Installation & Commissioning Instructions

For more information please call us on 

01993 824900

 or view our website at 

www.emmeti.co.uk

Gerpex Press Fit System

Gerpex Press Fit System

2. Installation

2.6 Pressure drops

Pressure drops across Gerpex and Gerpex Press 
Fittings can be calculated using data shown in the 
GERPEX System Technical Product Guide which can 
be found at www.emmeti.co.uk

2.7 Pipe cutting

The pipe must be cut at a 90

o

 angle and be cut 

perfectly straight. A rotary pipe slice is recommended 
for sizes 26mm and greater to ensure that the pipe is 
not deformed by the ratchet shear, see Fig 3.3 and 3.4.
An uneven cut will make calibration difficult.

2.8 Pipe preparation

Pipe preparation includes calibration and bevelling of 
the cut end of pipe with a purpose designed tool in 
readiness for the pipe to be inserted into the fitting. 
Failure to prepare the pipe in this way can lead to 
damage of the O-ring and the possible failure of a fitting. 

To calibrate the pipe the tool must be rotated into the 
end of the pipe in a clockwise motion as shown in Fig 
3.5 and 3.6:

To bevel the internal edge of the pipe the tool must 
be rotated clockwise which will remove and bevel 
the inner edge of the pipe. This prepares the pipe for 
insertion into the fitting.

Fig 3.3

Fig 3.4

Fig 3.5

Fig 3.6

The Emmeti calibration tool can be fitted to a battery 
powered drill to speed up the process. Please take care 
not to place undue pressure if calibrating in this way. 

Summary of Contents for Gerpex Press Fit













Reviews: