EMKO ESM- 20 Series, Manual

Page: 2 / 3

: Process � nput type select � on ; (Default: )
: J type (Fe,Cu,N � ) Thermocouple , -200ºC,900ºC ; -328ºF,1652ºF
: K type (N � ,Cr,N � ) Thermocouple , -200ºC,1300ºC ; -328ºF,2372ºF
: R type (Pt13%RhPt) Thermocouple , 0ºC,1700ºC ; 32ºF,3092ºF
: S type (Pt10%RhPt) Thermocouple , 0ºC,1700ºC ; 32ºF,3092ºF
: T type (Cu,Cu,N
� ) Thermocouple , -200ºC,400ºC ; -328ºF,752ºF
: Pt - 100 , -200ºC,650ºC ; -328ºF,1202ºF
: Pt - 100 , -199.9ºC,650.0ºC ; -199.9ºF,999.9ºF
: Un
� t Select � on. or can be chosen. (Default )
: Operat � on Scale m � n � mum (Low L � m � t) value. It changes
accord � ng to the process � nput type and scale. (Default: -200)
: Operat � on Scale max � mum (H � gh L � m � t) value. It changes
accord � ng to the process � nput type and scale. (Default: 900)
: Process Set value Low L � m � t. M � n � mum set value � s def � ned w � th
th � s parameter. It changes accord � ng to the process � nput type and
scale. (Default: -200)
: Process Set value H
� gh L � m � t. Max � mum set value � s def � ned w � th
th � s parameter. It changes accord � ng to the process � nput type and scale.
(Default: 900)
: D
� splay offset for process value. It can be adjusted from -10% of
scale to 10% of scale. It � s added to the process d � splay value.
(Default: 0)
Ma � n Screen
Press PSET
Button.
Press � ncrement
or decrement
button to change
Process Set value.
Ma � n Screen
Press ASET/OK Button
to save new Process
set value and return
the ma � n screen.
Press
ASET/OK
Button.
Press � ncrement or
decrement button
to change Alarm1
Set value.
Press ASET/OK
Button to save
new Alarm set
value and return
the ma � n screen.
Press � ncrement
or decrement
button to change
Alarm2 Set value.
Press ASET/OK
Button to save
new Alarm set
value and return
the ma � n screen.
Ma � n Screen
Ma � n Screen After 5 sec. Password Screen
To enter Program menu
press button for 5
seconds. Press ASET/OK
Button to access
Password Screen.
Enter Password w � th
� ncrement or
decrement buttons.
Approve
password w � th
ASET/OK Button.
Çal ış ma Ekran ı
To enter the Sensor
Break Output Value,
press ASET/OK
button for 5 seconds.
Change the Sensor
Break Output Value
w � th � ncrement and
decrement buttons.
Press PSET button to ex � t
w � thout sav � ng the value.
Press ASET/OK button to ex � t and save.
Start � ng the Tune operat � on
1- Enter to the programm � ng sect � on
2- Select or , parameter � n menu. Press ASET/OK
button for sav � ng the parameter and turn to the ma � n operat � on screen.
3- Observe that “ ” bl � nks � n set d � splay.
Note- For start � ng the Self Tune operat � on.
Heat � ng Tune Operat � on: Process value must be lower than process set
value at least 5% of full scale.
Cool � ng Tune Operat � on: Process value must be greater than process
set value at least 5%of the full scale . If th � s cond � t � on � s not okay,
Bl � nks on the screen for 10 seconds.
Cancel � ng Tune operat � on :
1- If sensor breaks;
2- If Tune operat � on can not be completed � n 8 hours;
3- Wh � le heat � ng Tune � s runn � ng, � f process value becomes greater than
Process Set value;
4- Wh � le cool � ng Tune � s runn � ng, � f process value becomes less than
Process Set value;
5- Wh � le Tune operat � on � s runn � ng, � f user changes the process set
value;
Then
Tune operat � on � s canceled, dev � ce cont � nues to run w � th former
PID parameters w � thout chang � ng PID parameters.
: Th � s parameter determ � nes, wh � ch output w � ll be Process control
output. If � s chosen, process output � s relay output, � f � s chosen,
process output � s SSR output. (Default: )
: Process Type Select � on. It can be or . (Default: )
: Process Control Type Select � on. It can be or .
(Default: )
: If tune parameter
� s set to , dev � ce start to Self Tune to
calculate PID parameters automat � cally. If tune parameter � s set to ,
dev � ce start to Auto Tune to calculate PID parameters automat � cally.
Th � s parameter � s shown � f = .
(Default: )
: Proport
� onal band. It can be adjusted from %1 to %100.
� f = , then th � s parameter can be observed. (Default: 10.0)
: Integral T � me. It can be adjusted from 0 to 3600 second.
� f = , then th � s parameter can be observed. (Default: 100)
: Der � vat � ve T � me. It can be adjusted from 0.0 to 999.9 second.
� f = , then th � s parameter can be observed. (Default: 25.0)
: Output Control Per � od. It can be adjusted from 1 to 150 second.
� f = , then th � s parameter can be observed. (Default: 10)
: Hysteres � s value. It can be adjusted from %0 to %50 of the
Scale ( - ). If = , then th � s parameter can be
observed. (Default: 3)
: Sensor Break Output Value. It can be adjusted from %0 to %100.
(Default: 0.0)
: Soft Start Set value. Dev
� ce operates � n Soft Start mode, unt � l the
temperature reaches Soft Start set value. (Default: )
: Soft Start Control Output. Th
� s parameter determ � nes soft start
mode control output percentage. (Default: 10.0)
: Soft Start Control T
� me. Th � s parameter determ � nes soft start
mode control t � me. (Default: 1)
: Password for access � ng to the programm � ng sect � on. It can be adjusted from
0 to 9999.
If
� s 0, password screen � s not observed. If � s d � fferent from 0 and user
enters to the menu pages w � thout enter � ng the password, all the menus can be
observed except protect � on menu . But dev � ce does not allow to do any
: Alarm Hysteres � s value. It can be adjusted from %0 to %50 of the Scale
( - ). (Default: 0)
: Alarm Type Select
� on. (Default: )
: Alarm Set Low L � m � t parameter. It can be adjusted from Operat � on Scale
m � n � mum to Alarm Set H � gh L � m � t. (Default: 0)
: Alarm Set H � gh L � m � t parameter. It can be adjusted from Alarm Set Low
L � m � t to Operat � on Scale m � n � mum. (Default: 500)
: Alarm on Delay T � me. It can be adjusted from 0 to 9999 seconds.
(Default: 0)
: Alarm off Delay T
� me. It can be adjusted from 0 to 9998 seconds. If � t � s
h � gher than 9998, � s seen on the screen and Alarm Latch � ng Output � s
selected. (Default: 0)
: Alarm Hysteres
� s value. It can be adjusted from %0 to %50 of the Scale
( - ). (Default: 0)
: Alarm type select
� on. (Default: )
: Alarm Set Low L � m � t parameter. It can be adjusted from Operat � on Scale
m � n � mum to Alarm Set H � gh L � m � t. (Default: 0)
: Alarm Set H � gh L � m � t parameter. It can be adjusted from Alarm Set Low
L � m � t to Operat � on Scale max � mum. (Default: 500)
: Alarm on Delay T � me. It can be adjusted from 0 to 9999 seconds.
(Default: 0)
: Alarm off Delay T
� me. It can be adjusted from 0 to 9998 seconds. If � t � s
h � gher than 9998, � s seen on the screen and Alarm Latch � ng Output � s
selected. (Default: 0)
NOTE: Alarm-2 parameters( , , , , , ) are act � ve,
� f parameter � s set as .
Note: User can ex � t from Set Value sect � on w � thout sav � ng the
values by press � ng button.
If no operat � on for 120 seconds, dev � ce automat � cally ex � ts from
Set Value sect � on .
Note: If user does not do anyth � ng for 120 seconds wh � le dev � ce � s on programm � ng
sect � on, dev � ce turns to operat � on screen.
Note: If user does not do anyth � ng for 120 seconds wh � le dev � ce � s on th � s sect � on,
dev � ce turns to operat � on screen.
Note-2: Sensor Break Output Value can be adjusted on programm
� ng sect � on too.
Access and Change Set Values Easy Access D � agram For Program Parameters
Easy Access D � agram For Sensor Break Output Value
Tune Operat � on
: Process Menu Parameters
: Control Menu Parameters
: Alarm Menu Parameters
: Protect � on Menu Parameter
Alarm Types
Note: If process � nput type select � on( ) � s changed, , ,
, , , , , , , , and
parameters may need to be updated accord
� ng to the � nput type
select � on.