EMKO EAOM-3 Series Manual Download Page 3

Equipment Use

Electrical control equipment for generating sets

Housing & Mounting

72 mm x 72 mm x 52 mm

Panel Cut-out

68 mm x 68 mm

Protection

NEMA4X (IP30 at front panel, IP20 at rear side)

Weight

Approximately 0.5 kg

Environmental Rating

Standard, indoor at an altitude of less then 2000 meters with non-condensing humidity

Operating / Storage Temperature -25ºC to +70ºC / -40ºC to +85ºC

Operating / Storage Humidity

90% max. (Non-condensing)

Installation Over Voltage Cat.

II appliances, portable equipment

Pollution Degree

II, Normal office or workplace, non-conductive pollution

Mode of Operation

Continuous

EMC

EN-61000-6-4, EMC generic emission standard for industrial equipment
EN-61000-6-2, EMC generic immunity standard for industrial equipment

Electrical Safety

EN-61010-1, safety requirements for electrical equipment for measurement, control and
laboratory use

Supply Voltage(

Z

)

Cranking Dropouts

Battery voltage can be 0V

Z

 for max. 100msn during cranking (battery voltage should be

at least nominal voltage before cranking)

Failure Indicators

Status Indicators

Relay Outputs

8 - 32 V

Z

0.5%

Alternator Frequency Range

From generator voltage

Generator Speed Measurement

Start relay (10A@28V

Z

)

Fuel relay (10A@28V

Z

)

Conf. Out relay (10A@28V

Z

)

Failed to engine start
High engine temperature
Low oil pressure
Speed failure
Battery charge failure
General failure

Hz./RPM
Engine running time
Engine start
Engine stop

Frequency Meas. Accuracy

15,6 to 99,9 Hz (15 to 300 VL-N

RMS)

Specifications

3

Manual and Remote Start Unit with Key Switch, 72x72 DIN Size

Summary of Contents for EAOM-3 Series











Reviews: