background image

.390

(10)

(6)

(8)

.235

.310

Warranty

All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If 

upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This 

warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.   

 

© 2019 Copyright EMG INC. All Rights Reserved.

PO BOX 4394 
SANTA ROSA, CA
95402  USA

P (707) 525-9941
F  (707) 575-7046
EMGPICKUPS.COM

0230-0308rA

 

   

                                 

                                 

INSTALLATION INFORMATION

 

EMG MODELS:

 GARY HOLT- GH SET

**Note:  Magnet Type: C (Ceramic) C/S (Ceramic/Steel)

   

                                 

                                 

*Note:  Logo Colors are not distinguished on the JH Set

   

                                 

                                 

1 PICKUP CABLE 15” (27.94cm) and 15” (38cm)

OUTPUT CABLE 6” (15cm)

4 CONNECT CABLES 5.5” (14cm)

BATTERY CABLE 7” (18cm)

-  9V  +

Installation notes:

 

All EMG Pickups are compatible with each other.  EMG accessories, the VLPF, EXG, SPC or RPC Controls can be added to any EMG Pickup System

without requiring an extra battery. DO NOT reconnect the bridge ground wire, EMG Pickups do not require string grounding. Use the 25K Ohm 

controls that are included for best results. If your output jack is a long panel style you will need a stereo jack, use a SwitchCraft 152B , soldering

will be required (see the bottom of page 2). Adjust the pickup level to the strings, and at a distance that works for you, experiment. Alternate

wiring diagrams are available at; emgpickups.com.

B245

2.75

1.50

3.09

3/48 MOUNTING HOLES

.900

.725

(69.8)

(38.1)

(22.8)

(18.4)

(78.5)

BATTERY

BUSS

2 PICKUP IN/ OUT
BATTERY BUSS

STEREO OUTPUT

JACK

1 VOLUME CONTROL (25K)
2 TONE CONTROLS (25K)

ADJUSTMENT
SCREWS & SPRINGS (2 pr)

L1 L2

L3

SPECIFICATIONS:

                                

MODEL

:

 

 

 

 

NECK 89R           

Single-Coil 

  Dual-Coil  

BRIDGE 81 

Logo Color 

                           

Copper 

 

 

 

 

 

Silver

Magnet 

Type 

 

   

 

 

     C/S

Resonant Frequency (KHz) 

 

 

 

3.80 

    

   2.00 

 

1.63 

Output Voltage (String) 

 

 

 

1.00 

    

   2.00 

 

3.00

Output Voltage (Strum) 

 

 

 

3.00 

    

   4.50 

 

4.50

Output Noise (60 Hz) 

 

 

 

-107 

    

   -109 

 

-100 

Output Impedance (Kohm) 

 

 

 

10 

    

   10 

 

10

Current 

@9V 

(Microamps) 

 160 

     80 

Battery 

Life 

(Hours) 

  1500 

     3000 

Maximum 

Supply 

(Volts 

DC) 

 27 

     27 

EMG 89R

1 TW P/P SWITCH
W/POT (25K)

TW PICKUP CABLE 16” (40.64cm)

Included IN THE SYSTEM:

 

Summary of Contents for NECK 89R

Page 1: ...an be added to any EMG Pickup System without requiring an extra battery DO NOT reconnect the bridge ground wire EMG Pickups do not require string grounding Use the 25K Ohm controls that are included for best results If your output jack is a long panel style you will need a stereo jack use a SwitchCraft 152B soldering will be required see the bottom of page 2 Adjust the pickup level to the strings ...

Page 2: ... cable under the pickup rather than in the control cavity rather than in the control cavity 6 IMPORTANT EMG Active pickups do not require a string ground wire 6 IMPORTANT EMG Active pickups do not require a string ground wire DO NOT Reconnect the string ground it is unnecessary DO NOT Reconnect the string ground it is unnecessary TONE B124rH MASTER TONE BRIDGE PICKUP BATTERY NEG T R S RED RED RED ...

Page 3: ...onnect cable from the Pickup Buss position 3 to the Master Tone control as shown 4 Strip the insulation from the switch wires and Insert them into the GREEN Terminal Block and tighten the screws with a small screwdriver The Bridge pickup goes to the BR Terminal The Neck Pickup goes to the NK Terminal The Output of the switch goes to the O Terminal If there is a ground wire coming from the switch i...

Page 4: ...lock and tighten the screws with a small screwdriver The Bridge pickup goes to the BR Terminal The Neck Pickup goes to the NK Terminal The Output of the switch goes to the O Terminal If there is a ground wire coming from the switch insert it into one of the black terminals on the terminal block 6 Plug the output cable onto the Pickup Buss Position 3 and push the connectors onto the jack as shown W...

Reviews: