Emerson VGC810 Installing And Operating Instructions Download Page 29

Page: 29 / 66

1592021021 XC1008-1011-1015D GB A5 r.1.5A 12.10.2009 XC1008-1011-1015D 29/66

otA2 =

for the optimization of the suction pressure/temperature, (dynamic set point) circuit 2

(dynamic set of suction circuit 2)

AI27

Probe 4 AUX calibration:

-12.0 ÷ 12.0

C; -120 ÷ 120 °F

AI28

Alarm relay on with auxiliary probe fault:
nu =

relay not present;

ALr:

all the C(i) outputs set as ALr;

ALr1:

all C(i) outputs set as ALr1,

ALr2:

all C(i) outputs set as ALr2.

6.1.6

Safety Digital Inputs (Di2-Di13)

DI2

Low pressure switch polarity (term. 52 - 53) – circuit 1:
oP=

LP d.i. enabled by voltage absence;

cL=

LP d.i. enabled by voltage presence.

DI3

Low pressure switch polarity (term. 56 - 57) – circuit 2:
oP=

LP d.i. enabled by voltage absence;

cL=

LP d.i. enabled by voltage presence.

DI4

High pressure switch polarity (term. 54 - 55) – circuit 1:
oP=

HP d.i. enabled by voltage absence;

cL=

HP d.i. enabled by voltage presence.

DI5

High pressure switch polarity (term. 58 - 59) – circuit 2:
oP=

HP d.i. enabled by voltage absence;

cL=

HP d.i. enabled by voltage presence.

DI6

Relay activated in case of pressure switch alarm:
nu =

no relay activation, only visual signalling;

Alr:

all the C(i) outputs set as ALr;

ALr1:

all the C(i)

outputs set as ALr1,

ALr2:

all the C(i) outputs set as ALr2

DI7

Compressor alarm inputs polarity - circuit 1
oP=

d.i. enabled by voltage absence;

cL=

d.i. enabled by voltage presence.

DI8

Compressor alarm inputs polarity - circuit 2
oP=

d.i. enabled by voltage absence;

cL=

d.i. enabled by voltage presence.

DI9

Fan alarm inputs polarity - circuit 1

oP=

d.i. enabled by voltage absence;

cL=

d.i. enabled by voltage presence.

DI10

Fan alarm inputs polarity - circuit 2

oP=

d.i. enabled by voltage absence;

cL= d.i. enabled by voltage presence.

DI11

Manual reset of compressor alarms signalled by d.i.
no =

automatic recover of alarm: regulation restart when the correspondent digital input is disabled

yES =

manual recover for the alarms of compressors

DI12

Manual reset of fan alarms signalled by d.i.
no =

automatic recover of alarm: a fan restarts when the correspondent digital input is disabled

yES =

manual recover for the alarms of fan

DI13

Relay activated in case of compressor or fan alarms:
nu =

no relay activation, only visual signalling;

Alr:

all the C(i) outputs set as ALr;

ALr1:

all the C(i)

outputs set as ALr1,

ALr2:

all the C(i) outputs set as ALr2

6.1.7

Digital Inputs (Di14-Di27)

DI14

Polarity of configurable digital input 1 (term 36-37)
oP:

the digital input is activated by opening the contact;

CL:

the digital input is activated by closing the contact.

DI15

Function of configur. configurable digital input 1 (term. 36-37)
ES1

= energy saving circuit 1

ES2

= energy saving circuit 2

OFF1 =

circuit 1 stand –by

OFF2 =

circuit 2 stand –by

LL1 =

liquid level alarm for circuit 1

LL2 =

liquid level alarm for circuit 2

Summary of Contents for VGC810



































































Search results

Summary of Contents for VGC810

Reviews:

Related manuals for VGC810

Brands by name

Popular brands

Emerson VGC810, Installing And Operating Instructions

Search results

Summary of Contents for VGC810

Reviews:

Related manuals for VGC810

Brands by name

Popular brands