background image

9

Blade Installation

Check to see that all connections are tight,
including ground, and that no bare wire is
visible at the wire connectors, except for the
ground wire. Do not operate fan until blades are
in place. Noise and fan damage could result.

WARNING

!

CEILING 
CANOPY

1-1/4" THREADED 
STUD (2)

#8 EXTERNAL TOOTH
LOCKWASHER (2) 

#8-32 KNURLED 
KNOB (2)

Figure 11

Figure 13

To avoid possible fire or shock, make sure that
the electrical wires are completely inside the
outlet box and not pinched between the ceiling
canopy and the ceiling.

WARNING

!

U.L. Model No.: CF3300

NOTE: The right hand and left hand blade flanges
are color coded and to be installed on the
matching color coded motor for correct operation
of the fan.

1.

Assemble one flange and one medallion to each
blade (sold separately) as shown (Figure 12) using
#10-32 x 18mm oval head screws (provided).

#10-32 X 18mm OVAL HEAD  
SCREWS (3 per flange)

FLANGE

BLADE (sold 
separately)

MEDALLION 

2.

Assemble remaining seven blades per previous
instructions.

NOTE: Take care not to scratch fan blades while
installing flanges. 

Blade Assembly Installation:

3.

With the fan suspended on the ceiling, install each
blade assembly onto the color coded motor hub by
sliding the tip of each blade flange into one of the
four large mounting holes on the exterior of each
motor hub. The flange tip and mounting hole are

#8-32 x 15mm FLAT HEAD SCREW 
(2 per flange/blade assembly)

FLANGE/BLADE ASSEMBLY

FAN MOTOR 
ASSEMBLY

NOTE: Take care not to scratch fan housing when
installing blades.

Figure 12

4.

Repeat flange/blade assembly instructions for

remaining three blades per each fan motor hub
assembly.

keyed to ensure correct installation, do not force
the parts together. Secure the blade assembly to
the motor hub using two #8-32 x 15mm flat head
screws provided (Figure 13).

NOTE: Be sure to match the blade flange color
code with the same matching color code on the
motor.

5.

Secure the ceiling canopy in place by sliding
lockwashers over the threaded studs and installing
the two knurled knobs (supplied). (Figure 11.)
Tighten the knurled knobs securely until the ceiling
canopy fits snugly against the ceiling and the hole
in the ceiling canopy is clear of the downrod. 

NOTE: Carefully remove the masking tape applied
to the center hole of ceiling cover, still taking
caution to not scratch downrod during
installation.

3.

Screw the two threaded studs (supplied) into the
tapped holes in the hanger bracket.

4.

Lift the ceiling canopy up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 11).

NOTE: Be careful not to scratch the blade surface
during installation.

Summary of Contents for ST CROIX CF3300AP

















Reviews: