Emerson Rosemount Oxymitter DR Reference Manual Download Page 55 | Manualshive

Page: 55 / 98

background image

2. Shut off the calibration gases at the cylinders and instrument air.
3. Disconnect the calibration gas and instrument air lines from the transmitter.
4. While facing the transmitter and looking at the Rosemount

™

label, remove screw

(18), cover lock (19), and captive washer (20) that secures the cover (17) on the left
side of the housing (11). Remove the cover to expose the terminal block (15).

5. Remove all signal and power wiring to the probe.
6. Remove insulation to access the mounting bolts.
7. Unbolt the transmitter from the stack and take it to a clean work area.
8. Allow the unit to cool to a comfortable working temperature.

4.4

Replace probe

Refer to

if you are using integral electronics or

if you are using remote

electronics. The numbers in the steps below correspond to the numbers of the items in
those figures.

Procedure

1. Bolt the transmitter to the stack and install the insulation.
2. Connect all signal and power leads at the probe.

for detailed wiring instructions.

3. Install left side cover (17) and ensure it is tight. Secure the cover using captive

washer (20), cover lock (19), and screw (18).

4. Connect the calibration gas and instrument air lines to the probe.
5. Turn on the calibration gases at the cylinders and turn on instrument air.
6. Restore power to the system.

Start up and operate transmitter with membrane keypad

or

operate transmitter with LOI

7. When the probe has reached operating temperature, calibrate it per

or

Calibrate with LOI

Note

Recalibrate whenever you replace electronic cards or the sensing cell.

4.5

Replace terminal block

WARNING

Opening the electronics housing will cause the loss of all hazardous permits. Opening the
electronics housing in hazardous areas may cause an explosion resulting in loss of
property, severe personal injury, or death.

You may need to get a hot work permit from your company safety officer before opening
the electronics housing.

Reference Manual

Maintenance and service

00809-0100-4880

October 2019

Rosemount Oxymitter DR

55

«
...
53
54
55
56
57
...
»

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Related manuals for Rosemount Oxymitter DR

Brand: AR Pages: 20

Brand: Valeport Pages: 25

Brand: Camille Bauer Pages: 62

Brand: Keithley Pages: 55

Brand: NanoEnTek Pages: 4

Brand: TA Instruments Pages: 7

SF6 Portable Monitor

Brand: Bacharach Pages: 2

Brand: Tektronix Pages: 20

EA Heightmaster +

Brand: PROLEC Pages: 38

Brand: Major tech Pages: 20

Panel Scope VPS10

Brand: Velleman Pages: 60

Brand: Maxtec Pages: 13

Brand: ICP DAS USA Pages: 340

ENERGY MAX EM400

Brand: Molectron Pages: 40

Brand: Bante Instruments Pages: 7

Brand: dallmeier Pages: 93

Pianovelle GRP3

Brand: Baldwin Pages: 34

Brand: FLIR Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands