Emerson Rosemount 8800D Series Reference Manual Download Page 65 | Manualshive

Page: 65 / 192

background image

55

Reference Manual

00809-0100-4772, Rev FA

Transducer Block

March 2016

Transducer Block

4.2.3

Alarm detection

Alarms are not generated by the transducer block. By correctly handling the status of the
channel values, the down stream block (AI) will generate the necessary alarms for the
measurement. The error that generated the alarm can be determined by looking at
BLOCK_ERR and XD_ERROR.

4.2.4

Status handling

Normally, the status of the output channels reflects the status of the measurement value,
the operating condition of the measurement electronics card, and any active alarm
condition. In Auto mode, Primary_Value reflects the value and status quality of the output
channels.

0x04000000

FLOW_SIGNAL_INJECT: The transducer block is

receiving its flow signal from an external signal

generator.

SEnSOr OFFLN

Informational only.

0x08000000

FLOW_EMULATION_MODE: The transducer block is

receiving its flow signal from the internal signal

generator.

SIGnAL SIMUL

Informational only.

0x10000000

SENSOR_OVERRANGE: The transducer has detected a

flow level that exceeds the upper sensor range. The

status associated with the primary value (PV) and

secondary value (SV) should also be BAD.

FAULT PV>SL

Verify process fluid

configuration. Reduce

flow to prevent damage

to the sensor.

0x20000000

PV_OVERRANGE: The transducer has detected a flow

level that exceeds the PV upper range. The status

associated with the PV and SV should also be

UNCERTAIN. The flow is still measurable, but accuracy is

not guaranteed.

Reduce flow below the PV

upper range value.

0x40000000

IN_LOW_FLOW_CUTOFF: The transducer has detected

that the flow has dropped below the configured

low-flow cutoff value. The reported flow value will now

damp to zero.

Informational only.

1.

If a transmitter power reset does not clear the error message, the electronics will need to be replaced.

2.

If the process temperature exceeds the specified limits of the temperature sensor, the indicated process temperature may not be within the rated
specifications of ± 2.2 °F (1.2 °C).

Table 4-4. Transducer Block Status Definitions (TB_ELECTRONICS_STATUS)

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

«
...
63
64
65
66
67
...
»

Summary of Contents for Rosemount 8800D Series

































































































































































































Reviews:

No comments

Related manuals for Rosemount 8800D Series

Brand: Oakton Pages: 4

Brand: AR Pages: 20

WJHD309 - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 101

Brand: Abbott Pages: 296

PLATINUM Series

Brand: Hach Pages: 64

BLITZFIRE Series

Brand: Task Force Tips Pages: 20

Brand: Mini Pages: 20

Brand: Burkert Pages: 192

Brand: Kawai Pages: 72

Brand: RaySafe Pages: 2

TWIN LASER GB II

Brand: Nicols Pages: 22

Brand: janitza Pages: 8

Brand: DAKOTA ULTRASONICS Pages: 51

Brand: R&S Pages: 35

WattNode Plus WNC-3D-240-FT10

Brand: CCS Pages: 43

Brand: novomatics Pages: 39

Brand: Acuity Pages: 46

Brand: Parkside Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands