Emerson Rosemount 2240S Reference Manual Download

Page: 80 / 194

Reference Manual

00809-0100-2240, Rev DA

Configuration/Operation

October 2017

Configuration/Operation

5.8.3

Capabilities

Virtual Communication Relationship (VCRs)

There are a total of 20 VCRs. One is permanent and 19 are fully configurable by the host system. 40 link
objects are available.

Table 5-6. Communication Parameters

Block Execution Times

Table 5-7. Execution Times

Network Parameter

Value

Slot Time

Maximum Response Delay

Minimum Inter PDU Delay

Block

Execution time (ms)

Multiple Analog Input (MAI)

Analog Input (AI)

Analog Output

Proportional/Integral/Derivative (PID)

Signal Characterizer (SGCR)

Integrator (INT)

Arithmetic (ARTH)

Input Selector (ISEL)

Control Selector (CS)

Output Splitter (OS)

Summary of Contents for Rosemount 2240S



































































































































































































Search results

Summary of Contents for Rosemount 2240S

Reviews:

Related manuals for Rosemount 2240S

Brands by name

Popular brands

Emerson Rosemount 2240S, Reference Manual

Search results

Summary of Contents for Rosemount 2240S

Reviews:

Related manuals for Rosemount 2240S

Brands by name

Popular brands