Emerson Rosemount 2240S Reference Manual Download

Page: 186 / 194

176

OUNDATION

™

Fieldbus Block Information

OUNDATION

™

Fieldbus Block Information

October 2017

Reference Manual

00809-0100-2240, Rev DA

C.7

Supported units

The Rosemount

™

2240S Multi-input Temperature Transmitter supports the following units:

Table C-15. Temperature

Table C-16. Length

Table C-17

lists supported units for Water Level Sensor (WLS) connected to the Sensor Bus.

Table C-17. Sensor Bus units

Value

Display

Description

1000

Kelvin

1001

deg C

Degree Celsius

1002

deg F

Degree Fahrenheit

Value

Display

Description

1010

Meter

1012

Centimeter

1013

Millimeter

1018

Feet

1019

Inch

Value

Description

Feet

Meter

Inch

Centimeter

Millimeter

Summary of Contents for Rosemount 2240S



































































































































































































Search results

Summary of Contents for Rosemount 2240S

Reviews:

Related manuals for Rosemount 2240S

Brands by name

Popular brands

Emerson Rosemount 2240S, Reference Manual

Search results

Summary of Contents for Rosemount 2240S

Reviews:

Related manuals for Rosemount 2240S

Brands by name

Popular brands