background image

Note

The device description loaded in the host system must be at the same
revision as this device.

Figure 3-3: Commissioning Tag

A. Device revision

Note

The device description loaded in the host system must be at the same
revision as this device. The device description can be downloaded from the
host system website or 

Emerson.com/Rosemount

 by selecting 

Download

Device Drivers

 under 

Product Quick Links

. You can also visit 

Fieldbus.org

 and

select 

End User Resources

.

3.3

Setting security switch

Prerequisites

Set Simulate and Security switch configuration before installation as shown
in 

Figure 3-4

.

The simulate switch enables or disables simulated alerts and simulated
AI Block status and values. The default simulate switch position is
enabled.

The Security switch allows (unlocked symbol) or prevents (locked
symbol) any configuration of the transmitter.

Default security is off (unlocked symbol).

The security switch can be enabled or disabled in software.

Use the following procedures to change the switch configuration:

November  2019

Quick Start Guide

Quick Start Guide

9

Summary of Contents for Rosemount 2051HT

































Reviews: