manualshive.com logo in svg

Emerson Rosemount 2051, Reference Manual

The Emerson Rosemount 2051 is a powerful and versatile pressure transmitter designed for accurate and reliable measurement. Our Quick Installation Manual provides step-by-step instructions for effortless set up. Download the manual for free at manualshive.com and gain access to all the essential information needed to maximize the performance of this exceptional product.

Share
Download
background image

77

Reference Manual 

00809-0100-4107, Rev BA

Section 5: Operation and Maintenance

April 2013

Operation and Maintenance

5.6.3

Recalling Factory Trim—analog output

The Recall Factory Trim—Analog Output command allows the restoration of the as-shipped 
factory settings of the analog output trim. This command can be useful for recovering from an 
inadvertent trim, incorrect Plant Standard or faulty meter.

Recalling Factory Trim - analog output with a Field 
Communicator

From the 

HOME

 screen, enter the fast key sequence and follow the steps within the Field 

Communicator to complete the digital to analog trim using other scale.

Recalling Factory Trim - analog output with AMS Device 
Manager

Right click on the device and, under the 

Method

 drop down menu, move cursor over 

Calibrate

 

and select 

Restore Factory Calibration

.

1.

Click 

Next 

to set the control loop to manual.

2.

Select 

Analog Output Trim

 under 

Select trim to recall

 and click 

Next

.

3.

Follow screen prompts to recall analog output trim.

Recalling Factory Trim - analog output with Local Operator 
Interface

Reference 

Figure 5-7

 for LOI instructions.

Figure 5-7. Recall Factory Trim – analog output with Local Operator Interface

Device Dashboard Fast Keys

3, 4, 3

EXTENDED MENU

CALIBRAT

CALIBRAT

DAMPING
TRANSFER FUNCT
SCALED VARIAB
ASSIGN PV
TAG
ALARM SAT VALUES
PASSWORD
SIMULATE
HART REV
BACK TO MENU
EXIT MENU

VIEW CONFIG
ZERO TRIM
UNITS
RERANGE
LOOP TEST
DISPLAY

EXTENDED MENU

EXTENDED MENU

EXIT MENU

CALIBRAT

ZERO TRIM
LOWER TRIM
UPPER TRIM
ANALOG TRIM

FACTORY RECALL

FACTORY RECALL

BACK TO MENU
EXIT MENU

FACTORY RECALL

SENSOR RECALL

ANALOG RECALL

ANALOG RECALL

BACK TO MENU
EXIT MENU

Summary of Contents for Rosemount 2051





































































































































































































































Reviews:

No comments

Related manuals for Rosemount 2051

Hach POCKET COLORIMETER II User Manual preview
POCKET COLORIMETER II
Brand: Hach Pages: 188
MadMan EMS-3 Operating Manual preview
EMS-3
Brand: MadMan Pages: 37
MADDALENA microCLIMA U Installation And Operating Instructions preview
microCLIMA U
Brand: MADDALENA Pages: 5
Radio Shack TRS-80 Owner'S Manual preview
TRS-80
Brand: Radio Shack Pages: 44
Radiodetection RD8100 Quick Locating Manual preview
RD8100
Brand: Radiodetection Pages: 2
Ralston Instruments LC10 Series Quick Start Manual preview
LC10 Series
Brand: Ralston Instruments Pages: 52
KROHNE OPTIMASS 7000 Handbook preview
OPTIMASS 7000
Brand: KROHNE Pages: 56
HANSA-FLEX HK S TKV User Manual preview
HK S TKV
Brand: HANSA-FLEX Pages: 23
Bartec TECH550PRO User Manual preview
TECH550PRO
Brand: Bartec Pages: 38
General DSM403SD User Manual preview
DSM403SD
Brand: General Pages: 12
Agilent Technologies LogicWave Installation Manual preview
LogicWave
Brand: Agilent Technologies Pages: 26
Casio Celviano AP-60R User Manual preview
Celviano AP-60R
Brand: Casio Pages: 44
Balluff BAE LX-XO-PL018-L S4 Series Quick Start Manual preview
BAE LX-XO-PL018-L S4 Series
Brand: Balluff Pages: 2
NCL DUAL-BLEND 4114 Installation And Setup Manual preview
DUAL-BLEND 4114
Brand: NCL Pages: 7
Bamo BAMOWIZ OX 452 User Manual preview
BAMOWIZ OX 452
Brand: Bamo Pages: 16
Labgear SQ-701 Instruction Sheet preview
SQ-701
Brand: Labgear Pages: 2
ST Beta 10P Series Operating Manual preview
Beta 10P Series
Brand: ST Pages: 32
Xylem mjk MagFlux Quick Start Manual preview
mjk MagFlux
Brand: Xylem Pages: 2

Brands by name

Popular brands

Load more brands