background image

Part Numbers

Key

Model No. Model No.

Model No.

Model No.

Model No.

No.

Description

HF948BS01 HF948W01 HF956BQ01 HF956BS01 HF956W01

1

J-Hook Bag Assembly:

761385

761385

761385

761385

761385

J-Hooks (2 each)

Hardware (2 each)

2

Hanger Assembly

761339

761339

761339

761339

761339

3

Pipe Nipple (8”)

761387-5

761387-2

4

Pipe Nipple (22”)

761387-6

761387

761387-BQ

761387-7

761387

5

Upper Canopy

761335-BS

761335

761335-BQ 761335-BS

761335

6

Lower Canopy

761336-BS

761336

761336-BQ 761336-BS

761336

7

Blades (Set of 3)

763095-BS

763095

763094-BQ 763094-BS

763094

8

Capacitor

*

Parts Bag, Containing:

761384

761384

761384

761384

761384

9

5/16-18 x 1/4” Setscrews (2 ea.)

10

Hairpin Clip

11

Clevis Pin

12

Cable Clamp (2 each)

13

Screw, M6 x 1/2” (6 each)

14

Spring Washer, M6 (6 each)

15

Blade Gasket (3 each)

16

Wire Connector (3 each)

17

Allen Wrench 

Owner's Manual

BP7311-2

BP7311-2

BP7311-2

BP7311-2

BP7311-2

Repair Parts Listing

1

2

4

5

6

10

11

17

13

12

16

14

7

15

8

9

3

Before discarding packaging material,
be certain all parts have been removed.

HOW TO ORDER REPAIR

PARTS

WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING
INFORMATION:
•  PART NUMBER
•  NAME OF ITEM
•  PART DESCRIPTION
•  MODEL NUMBER
The model number of your Fan will be
found on a label attached to the top
housing.
For repair parts, phone 1-800-654-3545.

Part No. F40BP73110002

Printed in China  09/10

Form No. BP7311-2

Air Comfort Products

DIVISION OF EMERSON ELECTRIC CO.

8100 W. Florissant • St. Louis, MO 63136

U.L. Model No.: HF948, HF956

BP7311-2 48 56" Heat Fans  9/7/10  3:25 PM  Page 8

Summary of Contents for HF948BS01









Reviews: