background image

S

tar Nut

Fiber 

Wa

s

her

Unpack dispenser components. 

On a firm, flat surface, carefully
straighten the copper tubing using
hands only.

Unscrew and remove threaded extension
from valve body. 

Do not discard, as you

will need this later

(See Figure 1)

.

Leave small washers in place.

Feed tubes down through the hole in 
the sink/counter until the base is at 
rest. Set faucet at desired angle.

From under sink, slide 2

1

4

"

 fiber washer

over faucet base. Reinstall threaded 
extension onto the base until snug. 
Thread star nut onto extension until 
snug (See Figure 2).

From under sink, slide 2

1

4

"

 fiber washer

over threaded extension. Thread star
nut onto extension until snug.

Hot & 

C

ool models only

Attach the quick connector to the ends
of the copper tubes running from the
dispenser.  

Install a 

white 

3/8

"

 tube into other end

of quick connector.

If sink/counter thickness exceeds 3/4" 

a hole diameter of 1

1

2

is required

.

An assistant may be needed to hold 

the dispenser head in place 

while securing the dispenser.

2

A

C

View / Wave

View / Wave

Hot & Cool models only

6

For a standard 1

1

2

" sink/counter hole 

Feed tubes down through the hole in 
the sink/counter until the base is at 
rest. Set faucet at desired angle.

Large washer required for sink holes 

larger

than 1

1

2

" or for porcelain sinks with radius 

or beveled holes.

Before feeding tubes through sink 
hole, remove extension. Place 2

1

4

"

 

large steel washer over threads on 
faucet base. Reinstall extension.

B

View / Wave

Faucet is factory-ready for installation 
into a standard 1

1

2

"

sink/counter hole.

1

5

8

"

 Small

Steel Washer

2

1

4

"

 Large

Steel Washer

1

5

8

"

 Rubber

Washer

Standard 1

1

2

" hole

Hole larger than 1

1

2

"

Installing into hole smaller than 1

1

2

"

S

tar Nut

Fiber 

Wa

s

her

Figure 1

Figure 2

INSTALLING THE FAUCET - VIEW/ WAVE

Property Damage: 

Do not pinch or 

b

reak copper

t

ub

in

g

. Do not 

d

i

s

tort the la

s

t 1 inch of t

ub

in

g

.

1

5

8

"

 Small

Steel Washer

1

5

8

"

 Small 

Rubber Washer

1

5

8

"

 Small

Steel Washer

1

5

8

"

 Small 

Rubber Washer

Summary of Contents for H-View-SS
















Reviews: