Emerson Fisher YD Instruction Manual Download Page 31

Page: 31 / 32

Instruction Manual

D100425X012

YD and YS Valves

July 2017

Key

Description

Part Number

Filament packing ring for NPS 3 and 4
with 12.7 mm (1/2 inch) stem (4 req'd)

14A0915X042

ENVIRO‐SEAL bellows seal spring

ENVIRO‐SEAL bellows seal spacer

12*

ENVIRO‐SEAL bellows seal upper wiper
For 9.5 mm (3/8 inch) and NPS 2 with 12.7 mm
(1/2 inch) stem

18A0868X012

For NPS 3 and 4 with 12.7 mm (1/2 inch)
stem

18A0870X012

13*

ENVIRO‐SEAL bellows seal bushing
For 9.5 mm (3/8 inch) stem (1 req'd),
for NPS 2 with 12.7 mm (1/2 inch) stem
(2 req'd)
S31600/PTFE

18A0820X012

R30006

18A0819X012

S31600/Cr Coated

11B1155X012

For NPS 3 and 4 with 12.7 mm (1/2 inch)
stem (1 req'd)
S31600/PTFE

18A0824X012

R30006

18A0823X012

S31600/Cr Coated

11B1157X012

13*

ENVIRO‐SEAL bellows seal bushing/liner
For 9.5 mm (3/8 inch) stem (1 req'd),
for NPS 2 with 12.7 mm (1/2 inch) stem
(2 req'd)
N10276 bushing, PTFE/glass liner

12B2713X012

N10276 bushing, PTFE/carbon liner

12B2713X042

For NPS 3 and 4 with 12.7 mm (1/2 inch)
stem (1 req'd)
N10276 bushing, PTFE/glass liner

12B2715X012

N10276 bushing, PTFE/carbon liner

12B2715X042

ENVIRO‐SEAL bellows seal Locknut

ENVIRO‐SEAL bellows seal pipe plug (2 req'd)

20*

ENVIRO‐SEAL bellows seal stem/bellows
assembly
1 Ply Bellows
S31600 trim mat'l, N06625 bellows mat'l

Key

Description

Part Number

NPS 1 w/ 9.5 mm (3/8 inch) stem

32B4224X012

NPS 1‐1/2 w/ 9.5 mm (3/8 inch) stem

32B4225X012

NPS 2 w/ 12.7 mm (1/2 inch) stem

32B4226X012

NPS 3 w/ 12.7 mm (1/2 inch) stem

32B4227X012

NPS 4 w/ 12.7 mm (1/2 inch) stem

32B4228X012

N06022 trim mat'l, N06022 bellows mat'l
NPS 1 w/ 9.5 mm (3/8 inch) stem

32B4224X022

NPS 1‐1/2 w/ 9.5 mm (3/8 inch) stem

32B4225X022

NPS 2 w/ 12.7 mm (1/2 inch) stem

32B4226X022

NPS 3 w/ 12.7 mm (1/2 inch) stem

32B4227X022

NPS 4 w/ 12.7 mm (1/2 inch) stem

32B4228X022

2 Ply Bellows
S31600 trim mat'l, N06625 bellows mat'l
NPS 1 w/ 9.5 mm (3/8 inch) stem

32B4224X032

NPS 1‐1/2 w/ 9.5 mm (3/8 inch) stem

32B4225X032

NPS 2 w/ 12.7 mm (1/2 inch) stem

32B4226X032

NPS 3 w/ 12.7 mm (1/2 inch) stem

32B4227X032

NPS 4 w/ 12.7 mm (1/2 inch) stem

32B4228X032

N06022 trim mat'l, N06022 bellows mat'l
NPS 1 w/ 9.5 mm (3/8 inch) stem

32B4224X042

NPS 1‐1/2 w/ 9.5 mm (3/8 inch) stem

32B4225X042

NPS 2 w/ 12.7 mm (1/2 inch) stem

32B4226X042

NPS 3 w/ 12.7 mm (1/2 inch) stem

32B4227X042

NPS 4 w/ 12.7 mm (1/2 inch) stem

32B4228X042

22*

ENVIRO‐SEAL bellows seal bonnet gasket
(graphite laminate)
NPS 1/2 through 1

12B6316X022

NPS 1‐1/2

12B6317X022

NPS 2

12B6318X022

NPS 3

12B6319X022

NPS 4

12B6320X022

ENVIRO‐SEAL bellows seal adaptor

ENVIRO‐SEAL bellows seal nameplate, warning

ENVIRO‐SEAL bellows seal drive screw (2 req'd)

36*

ENVIRO‐SEAL bellows seal pin

12B3951X012

ENVIRO‐SEAL bellows seal warning tag

ENVIRO‐SEAL bellows seal tie

ENVIRO‐SEAL bellows seal thrust ring

*Recommended spare parts

Summary of Contents for Fisher YD

































Search results

Summary of Contents for Fisher YD

Reviews:

Related manuals for Fisher YD

Brands by name

Popular brands

Emerson Fisher YD, Instruction Manual

Search results

Summary of Contents for Fisher YD

Reviews:

Related manuals for Fisher YD

Brands by name

Popular brands