manualshive.com logo in svg

Emerson Fisher N201 Series, Instruction Manual

Share
Download
Emerson Fisher N201 Series Instruction Manual Download Page 3

Type N201

3

l

PiVOT 

POinT

m

F

BEam 

hOrizOnTal

(lEVEl)

BEam in raisED 

POsiTiOn

D

E

sTanDarD TriP ValVE 

insTallaTiOn

maniFOlD

sCalE FramE

h

TriP ValVE

2 PiVOT 

POinT

C

i

P

h

K

J

TriP ValVE

3 (76)

1-1/4 

(32)

inChEs 

(mm)

TriP 

ValVE

J

J

BEam WhEn CylinDEr 

is nOT FillED

sCalE 

FramE

BEam sTOP

sCalE BEam

FrOm Charging PumP

TriP ValVE 

hOsE

TyPE n201 

FillEr ValVE

PilOT VaPOr 

PrEssurE FrOm 

air COmPrEssOr 

sTOragE TanK, 

Or auXiliary 

PrOPanE CylinDEr

sCalE BEam

Filling hOsE

aPPrOX. 1/5 

lEngTh OF 

sCalE BEam

alTErnaTE TriP ValVE insTallaTiOn # 2

(FOr TyPEs 1124a anD 1280a FairBanKs mOrsE sCalE)

alTErnaTiVE TriP ValVE 

insTallaTiOn #1

a

B

          c.  Drill a 5/8-inch (16 mm) hole through the scale 

               frame at this point.  

 

          d.  Attach the beam bar “L” to the clamp “M” with 

               two screws, and attach the clamp to the rear 

               of the scale beam with two screws.  

 

          e.  Remove locknut “D” and insert the trip valve 

               through the 5/8-inch (16 mm) hole.  

               Replace locknut. 
         f.  Using locknut “D” and “E”, position trip 

             valve so that it barely contacts the beam 

             bar ”L” with the scale in a 

             level position.  

  4.  Connect supply pressure (air or gas) at point “P”. 

       Recommended supply pressure is at least 30 psig 

       (2,1 bar), since regulator 2 is set at 30 psig 

       (2,1 bar) outlet pressure.  A 30 psig (2,1 bar) 

       supply is sufficient for pump discharge pressures 

       up to 350 psig (24,1 bar).  Regulator 1 is set at 

       3 psig (0,21 bar).    

 

note  

if propane vapor pressure is used, 

atmospheric or room temperature below 

8°F (-13°C) will limit supply pressure to 

below 30 psig (2,1 bar).  To assure tight 

shutoff of the filler valve in this event, 

refer to Table 1.    

Figure 3.

  Type N201 Installation

Summary of Contents for Fisher N201 Series









Reviews:

No comments

Brands by name

Popular brands

Load more brands