Emerson Fisher HS Instruction Manual Download Page 14

Page: 14 / 20

Instruction Manual

D100381X012

HS Valve

June 2019

Figure 7. Bushing Placement

GE99834

BUSHING

DETAIL A

BONNET
OR
LOWER FLANGE

5. Before removing the seat ring(s) check to see if the seat rings have been welded in place. If so, cut away the weld

before proceeding. Apply penetrating oil to the seat ring threads before attempting to remove the ring(s).

The following seat ring removal instructions are presented assuming a seat ring puller, as shown in figure 8, is being
used:

a. Place the proper size seat lug bar across the seat ring so that the bar contacts the seat lugs as shown in figure 8.

b. Insert a drive wrench and place enough spacer rings over the wrench so that the hold-down clamp will rest about

1/4 inch above the valve flange.

Figure 8. Seat Ring Puller

SEAT LUG BAR

AD5222-B
A1615/IL

DRIVE WRENCH

TURNING BAR

HOLD DOWN CLAMP

SPACER RINGS

Slip a hold-down clamp onto the drive wrench and secure the clamp to the valve with two cap screws (or two studs and
hex nuts) from the bonnet. Do not tighten the cap screws or nuts.

Summary of Contents for Fisher HS





















Search results

Summary of Contents for Fisher HS

Reviews:

Related manuals for Fisher HS

Brands by name

Popular brands

Emerson Fisher HS, Instruction Manual

Search results

Summary of Contents for Fisher HS

Reviews:

Related manuals for Fisher HS

Brands by name

Popular brands