6. PROGRAM
7.CD PLAY/PAUSE
8.LCD DISPLAY
9.CFD
10. VOLUME CONTROL
11.CD STOP SWITCH
12.CD SKIP-
13. TUNING
14. CD SKIP+
15. BAND SWITCH
16 SPEAKER
17. CASSETTE RECORD SWITCH
18. CASSETTE PLAY SWITCH
19. CASSETTE REW SWITCH
20. CASSETTE FWD SWITCH
21 CASSETTE STOP/EJECT SWITCH
22. CASSETTE PAUSE SWITCH
23. CASSETTE HOLDER
24 .ANTENNA
25. BACK COVER
26. SPEAKER OUTPUT
TERMINAL(RIGHT).
27 SPEAKER OUTPUT
TERMINAL(LEFT)
28. AC SOCKET
29. AUDIO OUT
30. VIDEO OUT
31. JOYSTICK TERMINAL
specifications
Frequency Range FM:88-108MHz,AM:530-1700KHz
Power Requirements
120V,60Hz
Specifications are subject to change for performance improvement without notice.
POWER SUPPLY
AC OPERATION
- THE AC POWER CORD IS LOCATED
- PLUG THE AC LINE CORD INTO ANY NORMAL HOUSEHOLD AC MAINS
OUTLET IN CORRECT VOLTAGE AND THE MAINS SOCKET.
STANDBY INDICATOR
When the power is connected to AC outlet, the STANDBY LED indicator will light up. You
have to press the POWER button on the unit or POWER button on the remote to turn on
the unit.
RADIO OPERATION
1. Connect the unit to the power source.
2. Slide the FUNCTION SWITCH to "RADIO" position.
3. Select desired wave band with the BAND SWITCH.
4. Tune to desired station by rotating the TUNING KNOB.
5. Gently rotate this control back & forth until you get the strongest, clearest sound.
6. The built-in MW(AM) or LW antenna and the SW antenna rod are directional. When
receiving SW broadcast, extend the SW ELESCOPIC ANTENNA in full length.
The strongest reception can be achieved by rotating the set for MW(AM) or LW or
Telescopic Antenna for FM or SW.
7. Adjust the VOLUME KNOB to your listening preference.
8. To turn off the radio, slide the FUNCTION SWITCH to "TAPE" position.
CASSETTE OPERATION
PLAYBACK OF CASSETTE
Be sure to tighten any slack tape in the cassette before use, using either a pencil or a
ball-point pen, simply insert the pen or pencil into the centre of spool and rotate to remove
slackess.
Depress the STOP/EJECT button to open the cassette door.
Insert the cassette into the compartment with the open end facing upward and the full reel
on the left hand side, push the cassette well down and close the door, be sure not to touch
the tape surface. Set the Function switch to "TAPE" position and press the cassette play
button. To stop playback, press the STOP/EJECT button again.
AUTO STOP
When the tape reaches the end during playback or recording, the built-in auto stop system
will release the depressed play, record keys. The auto stop system operates while
recording from the built-in radio or CD player, only the cassette function is brought
automatically to stop mode and the radio or CD Player will continue to play.
TAPE RECORDING
A. Install a cassette tape.
B. Set FUNCTION SWITCH to "RADIO" position. After selecting the desired band and
tune the TUNING KNOB to desired broadcast station. Then push down RECORD
BUTTON and PLAY BUTTON simultaneously.
C. After recording the desired broadcast, depress the STOP/EJECT BUTTON lightly, and
then set FUNCTION SWITCH to "TAPE" position in order to listen to the recorded
broadcast.
D. If you desire to play recorded broadcast, please follow the instructions explained in
playback section.
Note: Tape recording is also available for VCD/CD/MP3 playback (set FUNCTION
SWITCH to "VCD/CD/MP3" position). Similar as radio recording.
External MIC recording: Set FUNCTION SWITCH to "TAPE" position, press the RECORD
BUTTON and PLAY BUTTON simultaneously and speak through external MIC.
TYPES OF CASSETTE
Use only good quality cassettes (IEC TYPE 1) for making recordings. May be used to
replay other types of cassette but is unable to make proper recordings on these more
specialized tapes.
The use of C120 cassettes is NOT recommended in this machine.
PROTECTING RECORDING
24
27
26
25
28 29 30
31
8
10
3
11
5
6
13
12
4
9
7
2
14
17 18 19 20 21 22 23
15
16
16
8
10
3
11
5
6
13
12
4
9
7
2
14
17
18
19
20
21
22
23
15
16
16
24
27
26
25
28
29
30
31
6.PROGRAMA
7.REPRODUCCIÓN/PAUSA
DEL CD
8.PANT
ALLA LCD
9.CFD
10.CONTROL DE VOLUMEN
11.BOTÓN DETENER DEL
CD
12.SALT
O DEL CD -
13.SINTONIZADOR
14.SALT
O DEL CD +
15.BOTÓN DE BANDAS
16.ALT
AVOZ
17.BOTÓN DE GRABACIÓN DEL CASETE
18.BOTÓN REPRODUCIR DEL CASETE
19.BOTÓN RETROCEDER DEL CASETE
20.BOTÓN ADELANT
AR DEL CASETE
21.BOTÓN DETENER/EYECTAR DEL
CASETE
22.BOTÓN PAUSA
DEL CASETE
23.SOSTÉN DEL CASETE
24.ANTENA
25.TAP
A TRASERA
26.SALIDA DEL
AL
TA
VOZ (DERECHA)
27.SALIDA DEL
AL
TA
VOZ (IZQUIERDA)
28.ENTRADA AC
29.SALIDA DE
AUDIO
30.SALIDA DE VÍDEO
31.SALIDA DE LOS MANDOS
ESPECIFICACIONES
Rango de frecuencia:
FM: 88-108MHz, AM: 530-1700KHz
Requisitos de energía:
120V, 60Hz
Las especificaciones estar sujetas a cambio con el fin de hacer mejoras sin previo aviso.
FUENTES DE ENERGÍA
Con energía AC
-Conecte el cordón AC
-Enchufe el cordón AC a un tomacorriente doméstico que cuente con el voltaje correcto.
INDICADOR STANDBY
Cuando el aparato se encuentre conectado a la electricidad, la luz indicadora STANDBY
se
iluminará. Debe presentarse el botón POWER en el aparato o en el control remoto para encender
el equipo.
FUNCIONAMIENTO DE LA
RADIO
1.Conecte el equipo al tomacorriente.
2.Coloque el selector de FUNCIONES en la posición RADIO.
3.Seleccione la banda deseada con el selector de BANDAS.
4.Sintonice la estación deseada girando el control de sintonización.
Summary of Contents for EMMC35881
Page 2: ......
