Emerson Dixell XR20T, Operating Instructions Manual

Page: 22 / 41

1592040000 XR20-30-60-70T EN v1.5 2021.06.22 XR20-30-60-70T 22/41
dEF od2
Optimized defrost
no Pr2 n(0); Y(1)
dEF dSt
Temperature sampling time during an
optimized defrost (valid only if od2=yes)
30 Pr2 sec 1 to 255 sec
dEF SYd
Type of synchronized defrost
nU Pr2 nu(0); SYn(1); nSY(2)
dEF dt1
Differential temperature for latent heating
control
0.1 Pr2 °C 0.1 to 1.0°C
dEF ErS
Restart regulation after dripping time, when
defrost Syd = nSY
no Pr2 n(0); Y(1)
FAn FAP Probe selection for evaporator fan P2 Pr2 nP(0); P1(1); P2(2); P3(3); P4(4)
FAn FSt Evaporator fan stop temperature 10.0 Pr2 °C
[-50.0°C to 50.0°C]
[-58.0°F to 122.0°F]
FAn HYF Evaporator fan regulator differential 2.0 Pr2 °C
[0.1°C to 25.0 °C]
[0.1°F to 45.0°F]
FAn FnC Evaporator fan operating mode C_n Pr2 C-n(0); O-n(1); C-Y(2); O-Y(3)
FAn Fnd Evaporator fan delay after defrost cycle 1 Pr2 min 0 to 255 min
FAn FCt
Differential temperature for cyclic activation
of evaporator fans (o=disabled)
0 Pr2 °C
[0°C to 50°C]
[0°F to 90°F]
FAn FSU Evaporator fan operating mode Std Pr2 Std(0); FoF(1); Fon(2)
FAn Ft Evaporator fan controlled during defrost no Pr2 n(0); Y(1)
FAn Fon
Evaporator fan ON time in normal mode
(with compressor OFF)
5 Pr2 min 0 to 255 min
FAn FoF
Evaporator fan OFF time in normal mode
(with compressor OFF)
10 Pr2 min 0 to 255 min
FAn Fo1
Evaporator fan ON time in energy saving
mode (with compressor OFF)
5 Pr2 min 0 to 255 min
FAn FF1
Evaporator fan OFF time in energy saving
mode (with compressor OFF)
10 Pr2 min 0 to 255 min
FAn Fd1 Evaporator fan delay 0 Pr2 sec 0 to 255 sec
FAn Fd2 Evaporator fan delay after closing door 0 Pr2 sec 0 to 255 sec
FAn FAC Probe selection for condenser fan P3 Pr2 nP(0); P1(1); P2(2); P3(3); P4(4)
FAn St2 Set Point 2 regulation (for condenser fan) 10.0 Pr2 °C
[-100.0°C to 150.0°C]
[-148.0°F to 302.0°F]
FAn Hy2 Set Point 2 differential (for condenser fan) 10.0 Pr2 °C
[0.1°C to 25.0°C]
[0.1°F to 45.0°F]
FAn FCC Condenser fan operating mode C_n Pr2 C-n(0); O-n(1); C-Y(2); O-Y(3)
FAn Fd3 Condenser fan activation delay 0 Pr2 sec 0 to 255 sec
FAn Fd4 Condenser fan deactivation delay 0 Pr2 sec 0 to 255 sec
AUS ACH Type of control for auxiliary regulator CL Pr2 CL(0); Ht(1)
AUS SAA Set point for auxiliary regulator 5.0 Pr2 °C
[-100.0°C to 150.0°C]
[-148.0°F to 302.0°F]
AUS SHy Auxiliary regulator differential 2.0 Pr2 °C
[0.1°C to 25.0°C]
[0.1°F to 45.0°F]
AUS ArP Probe selection for auxiliary regulator nP Pr2 nP(0); P1(1); P2(2); P3(3); P4(4)
AUS Sdd
Auxiliary regulator disabled during any
defrost cycle
no Pr2 n(0); Y(1)
AUS btA Base time for parameters Ato and AtF SEC Pr2 SEC; Min
AUS Ato Interval of time with auxiliary output ON 0 Pr2 sec 0 to 255 sec/min
AUS AtF Interval of time with auxiliary output OFF 0 Pr2 sec 0 to 255 sec/min
ALr ALP Probe selection for temperature alarms P1 Pr1 nP(0); P1(1); P2(2); P3(3); P4(4)
ALr ALC
Temperature alarms configuration: relative,
absolute
Ab Pr1 rE(0); Ab(1)
ALr ALU High temperature alarm 150.0 Pr1 °C
°C[0.0° to 50.0° or ALL to
150.0°]
°F[0.0° to 90.0° or ALL to 302.0°]