background image

2

Information for DECT Product

Hearing aid Compatibility (HAC)

Interference information

This telephone is compliant with the DECT 6.0 standard which 
operates in the 1.92GHz to 1.93GHz frequency range. Installation of 
this equipment is subject to notification and coordination with UTAM.  
Any relocation of this equipment must be coordinated through and 
approved by UTAM.  UTAM may be contacted at 1-800-429-8826.   

21

Should you have any questions or problems concerning this 
product, please contact our customer service department at:

1-877-768-8483 (Toll Free)

Monday - Thursday: 9AM - 5PM (EST)

Friday: 9AM - 3PM (EST)

or

via e-mail at 

[email protected]

Warranty service not provided

This warranty does not cover damage resulting from accident, 
misuse, abuse, improper installation or operation, lack of reasonable care, and 
unauthorized modification. This warranty is voided in the event any unauthorized 
person opens, alters or repairs this product. All products being returned to the 
authorized service center for repair must be suitably packaged.

Limitation of Warranty:

● 

THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE

   TO THIS PRODUCT.  ALL OTHER WARRANTIES, EXPRESS OR IMPLIED
    (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR
   FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED.
   NO VERBAL OR WRITTEN  INFORMATION GIVEN BY SOUTHERN TELECOM
    INC.  IT’S AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY 
    OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.

The telephone company may make changes in its communications facilities, equipment, 

operations or procedures where such action is required in the operation of its business and not 

performance of your telephone equipment, the telephone company must give you adequate 

notice, in writing, to allow you to maintain uninterrupted service.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) This device may not cause harmful interference; and (2) This device must accept 

any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class  B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not occur in a particular 

installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which can be 

ect the 

Interference by one or more of the following measures:

  Reorient or relocate the receiving antenna. 


 

Increase the separation between the equipment and receiver.

antenna is connected. 
Consult the dealer or an experienced radio/TV technician for help.

The telephone meets FCC standards for Hearing Aid Compatibility.

NOTICE: Changes or modifications not expressly approved by the party

responsible could void the user’s authority to operate the equipment.

Summary of Contents for DECT 6.0 EM6113













Reviews: