Emerson Damcos Service Manual Download Page 94

Page: 94 / 144

Service Manual

Damcos LPU: Replace Pump in LPU

SM 8000-100-01 Ed 04

February 2017

Oil the new stator and place it with slot for pin in
same direction as slot in valve block

Be sure the small pin is in place on stator!

Turn in the stator. When stator is turned to correct
rotational position press it down to same level as
mounting tool.

Check the height of stator.
Stator is pressed until extension above valve block
surface is 19 mm. This should correlate with the
height of mounting tool as of point 8.

10.

Check suction pipe filter for contamination. If nec-

essary clean the filter.
Mount the suction pipe.

11.

Rotor with pistons is placed on stator or in LPU

block depending on mounting direction of LPU.
Rotor coupling must be placed in same direction as
corresponding slot in motor shaft.

Replace Pump in LPU

It is essential
that the height
of stator is
exactly 19 mm!

Summary of Contents for Damcos

















































































































































Search results

Summary of Contents for Damcos

Reviews:

Related manuals for Damcos

Brands by name

Popular brands

Emerson Damcos, Service Manual

Search results

Summary of Contents for Damcos

Reviews:

Related manuals for Damcos

Brands by name

Popular brands