Emerson Damcos Service Manual Download Page 52 | Manualshive

Page: 52 / 144

background image

Service Manual

Damcos LPU: Troubleshooting Guide LPU

SM 8000-100-01 Ed 04

February 2017

52

Solenoid valve not working

Action:

•

Check that solenoid valve is energized (230 V on terminals “N” and “SV”).

•

If coil is energized, but solenoid valve does not work, the resistance of the coil is measured (LPU-
D). The coil must have a resistance of approximate 520



for LPU-D. Due to a diode bridge resis-

tance cannot be measured for LPU-S coil. Another way to check the coil is to loosen it and try to
lift the coil when energized. If coil does not work, it is replaced.

•

If coil works, the valve is to be replaced. See “Replace Solenoid Valve in LPU-D” on page 107.

«
...
50
51
52
53
54
...
»

Summary of Contents for Damcos

















































































































































Reviews:

No comments

Related manuals for Damcos

Brand: CORNING Pages: 48

Brand: Eberg Pages: 14

Brand: GAS Pages: 214

UEYPOPL/12-4Q/3D

Brand: Cristec Pages: 54

Brand: NextBase Pages: 52

Brand: Porter-Cable Pages: 24

Brand: ECG Pages: 116

Brand: K&S BASIC Pages: 23

Brand: FEESER Pages: 32

Brand: Panacom Pages: 10

Brand: Roberts Pages: 12

Brand: Whisper Power Pages: 40

Brand: Johnson Controls Pages: 8

Brand: Lenox Pages: 17

Brand: Rohde & Schwarz Pages: 299

Brand: Tentacle Pages: 14

Brand: Durabrand Pages: 28

Brand: Master Pages: 117

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands