background image

READ AND SAVE THESE INSTRUCTIONS

Installation Instruction on

New CSA Hanging Device

Always properly install the ceiling fan mounting plate to a structural ceiling joist that is capable of
reliably supporting at least 50 pounds. 

INSTALLATION INSTRUCTIONS

1.

Slip the loop of the short steel support cable onto the flat
washer, lockwasher and 2” lag screw (supplied). Attach
the short steel support cable through the center hole of
the outlet box into the supporting joist by securely
tightening the flat washer, lockwasher and 2” lag screw
(Figure 1). The support cable lag screw must be installed
such that it is structurally independent of the outlet box.
Pre-drill the support joist with a 9/64” diameter drill to
prevent splitting the joist.

2.

Pull the electrical supply wires and support cable through
the center opening of the ceiling cover (Figure 2).

3.

Install the ceiling cover and hanger bracket together onto
the outlet box using the two screws supplied with the
ceiling fan. Discard the screws that were supplied with
the electrical box. The hanger bracket will nest into the
ceiling cover between the raised guides on the bottom
surface of the cover. The center hole of the ceiling cover
provides visual access to view installation of the outlet
box screws into the threaded mounting holes of the box
(Figure 3).

4.

Pull the electrical supply wires and support cable through
the opening on the back side of the hanger bracket for
installation of the fan’s hanger ball.

PRELIMINARY PROCEDURES FOR

EXTRA SUPPORT HANGING SYSTEM

SHORT STEEL 
SUPPORT CABLE

JOIST

2" LAG SCREW

FLAT WASHER

LOOP

CENTER HOLE

LOCKWASHER

FLAT WASHER, 
LOCKWASHER, & 
2" LAG SCREW

DRYWALL CEILING

SHORT STEEL 
SUPPORT CABLE

OUTLET BOX

ELECTRIC

OUTLET BOX

Figure 1

Turning off wall switch is not sufficient.
To avoid possible electrical shock, be sure
electricity is turned off at the main fuse box before
wiring. All wiring must be in accordance with
National and Local codes and the ceiling fan must
be properly grounded as a precaution against
possible electrical shock.

WARNING

!

MOUNTING SCREW (2)

TAB

HANGER BRACKET

CEILING 
COVER

Figure 2

To avoid possible fire or shock, do not pinch electrical
wires between the ceiling cover and hanger bracket, or the
electrical box and the ceiling cover.

WARNING

!

Summary of Contents for CORSAIR 44"















Reviews: