background image

This Manual Is Designed to Make it as Easy as Possible for You

to Assemble, Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver
One 1/4" blade screwdriver
One stepladder
One wire stripper
Three wire connectors (supplied)

MATERIALS

Wiring, electrical box and box connectors must be of type
required by local code. The minimum wire would be a
3-conductor (2-wire with ground) of size shown at right.

Installed Wire Length

Wire Size A.W.G.

Up to 50 ft.

14

50 - 100 ft.

12

Unpacking Instructions

For your convenience, check-off boxes are provide next to each step. As each step is completed, place a
check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.

3

Before assembly your ceiling fan, refer to section on
proper method of wiring your fan (page 5). If you feel
you do not have enough wiring knowledge or experi-
ence, have your fan installed by a licensed electrician.

WARNING

!

This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson. Substitution of parts or accessories not
designated for use with this product by Emerson
could result in personal injury or property damage.

WARNING

!

Do not install or use fan if any part is damaged or
missing. Call Toll-Free:

1-800-654-3545

WARNING

!

1.Check to see that you have received the following

parts:

a. Crystal glass housing
b. Mounting plate/light fitter

c. Motor assembly

d. Switch housing/light fitter
e. Four glass shades

f. Five fan blades

g. Five blade flanges
h. One loose parts bag containing:

1. Fifteen 3/16-24 x 9/32" phillips head screws.
2. Ten 1/3-20 x 1/2” phillips head screws.
3. One wood ball (small) with chain.
4. One wood ball (large) with chain.
5. Three wire connectors.
6. Four 3/16-24 x 3/8" phillips head screws.
7. Four Nuts-Hexlock 1/4-20. 

NOTE: Place the parts from the loose parts bag in
a small container to keep them from being lost. If
any parts are missing, contact your local retail or
catalog outlet for replacement before proceeding.

Summary of Contents for CF875SPB00









Reviews: