background image

2

This Manual Is Designed to Make it as Easy as Possible for You to

Assemble, Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver
One stepladder
One 1/4” blade screwdriver
One wire stripper
Three wire connectors (supplied).

MATERIALS

Wiring outlet box and box connectors must
be of type required by the local code. The
minimum wire would be a 3-conductor (2-
wire with ground) of the following size:

Before assembly your ceiling fan, refer to
section on proper method of wiring your
fan (page 7). If you feel you do not have
enough wiring knowledge or experience,
have your fan installed by a licensed
electrician.

WARNING

!

Do not install or use fan if any part is
damaged or missing. Call Toll-Free:

1-800-654-3545

WARNING

!

This product is designed to use only
those parts supplied with this product
and/or any accessories designated
specifically for use with this product by
Emerson Electric Co. Substitution of
parts or accessories not designated for
use with this product by Emerson
Electric Co. could result in personal
injury or property damage.

WARNING

!

Installed Wire Length Wire Size A.W.G.

Up to 50 ft.

14

50-100 ft.

12

Unpacking Instructions

For your convenience, check-off boxes are provided next to each step. As each
step is completed, place a check mark in the box. This will insure that all steps
have been completed and will be helpful in finding your place should you be
interrupted.

1. Check to see that you have received

the following parts:

NOTE: If you are uncertain of part
description, refer to exploded view
illustration.

a. Fan motor assembly

b. One switch housing assembly
c. Five fan blades
d. One ceiling cover
e. Five blade flanges
f. One hanger ball/downrod assembly
g. One hanger bracket

h. One coupling cover

i. One loose parts bag containing:

1. Sixteen 3/16-24 x 1/2”

slotted Phillips blade screws

2. Sixteen blade washers
3. Eleven 1/4-20 x 1/2” Phillips oval

head flange screws

4. One wood pendant
5. One coupling
6. Three wire connectors
7. Two threaded studs
8. Two knurled knobs
9. Two lockwashers

10. One clevis pin
11. One hairpin clip

COUPLING
COVER

CEILING
COVER

BLADE
FLANGES

SWITCH CUP
ASSEMBLY

HANGER
BRACKET

HANGER BALL/
DOWNROD
ASSEMBLY

LOOSE
PARTS
BAG

FAN MOTOR
ASSEMBLY

FAN
BLADES

BP7287 60" DESIGNER FAN  3/10/05  10:42 AM  Page 2

Summary of Contents for CF760AB00













Reviews: