background image

7

OUTLET BOX

BLACK SUPPLY WIRE

BLACK/WHITE RECEIVER WIRE

BLACK FAN WIRE

BLUE FAN WIRE

BLUE RECEIVER 
WIRE

YELLOW RECEIVER 
WIRE 

DO NOT USE

CEILING COVER

WHITE RECEIVER WIRE

WHITE FAN WIRE

WIRE CONNECTOR

RECEIVER

WHITE SUPPLY
WIRE

SUPPLY GROUND
WIRE (GREEN OR 
BARE)

HANGER BALL
GROUND WIRE
(GREEN)

HANGER BRACKET
GROUND WIRE
(GREEN)

HANGER BRACKET

BLACK RECEIVER WIRE

OPEN 

PORTION OF 

RECEIVER 

HERE

Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box
before wiring. All wiring must be in accordance with
National and Local codes and the ceiling fan must be
properly grounded as a precaution against possible
electrical shock.

WARNING

!

Figure 12

If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician. 

CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan and light kit or receiver.

1.

Pull the wire leads, coming from the end of the
downrod, and the supply wires through the open
side of the hanger bracket. (Figure 12).

2.

Position the SW105 Receiver (supplied) in the ceil-
ing cover so that the flat side of the receiver faces
up and the open portion of the receiver is to the
right, as shown in Figure 12.

3.

Using wire connectors (supplied), make wiring con-
nections as follows (Figure 12 and 13):

a.

Connect the white fan wire and the white supply
wire to the white receiver wire (AC IN/
MOTOR N).

b.

Connect the black fan wire to the black receiver
wire (TO MOTOR L).

c.

Connect the black supply wire to the black/white
receiver wire (AC IN L).

d.

Cut off the ends of the blue and yellow receiver
wires and strip back insulation 1/2-inch from the
ends of the wires.

e.

Connect the blue fan wire to the blue receiver
wire (BOTTOM LIGHT).

f.

Connect the green ground wires from the hang-
er bracket and the hanger ball to the supply
ground wire (bare or green).

NOTE: Do not use capped yellow wire.

How to Wire Your Ceiling Fan

U.L. Model No.:  CF3000

Summary of Contents for CF3000BS00 ORIGAMI

















Reviews: