Emerson 8700 Series Reference Manual Download Page 48 | Manualshive

Page: 48 / 136

background image

Reference Manual

00809-X0100-4793, Rev CA
August 2004

4-9

Rosemount 8742C

FEATURES_SEL

FEATURES_SEL is used to turn on any of the supported features. The default
setting of the Rosemount 8742C does not select any of these features.
Choose one of the supported features if any.

MAX_NOTIFY

The MAX_NOTIFY parameter value is the maximum number of alert reports
that the resource can have sent without getting a confirmation, corresponding
to the amount of buffer space available for alert messages. The number can
be set lower, to control alert flooding, by adjusting the LIM_NOTIFY
parameter value. If LIM_NOTIFY is set to zero, then no alerts are reported.

PlantWeb

™

Alarms

The Resource Block will act as a coordinator for PlantWeb alarms.
There will be three alarm parameters (FAILED_ALARM,
MAINT_ALARM, and ADVISE_ALARM) which will contain
information regarding some of the device errors which are
detected by the transmitter software. There will be a
RECOMMENDED_ACTION parameter which will be used to

display the recommended action text for the highest priority alarm.
FAILED_ALARM will have the highest priority followed by MAINT_ALARM
and ADVISE_ALARM will be the lowest priority.

FAILED_ALARMS

A failure alarm indicates a failure within a device that will make the device or
some part of the device non-operational. This implies that the device is in
need of repair and must be fixed immediately. There are five parameters
associated with FAILED_ALARMS specifically, they are described below.

FAILED_ENABLED

This parameter contains a list of failures in the device which makes the
device non-operational that will cause an alarm to be sent. Below is a list
of the failures with the highest priority first.

1.

Output Board Electronics Failure

2.

Sensor Board Electronics Failure

3.

Output Board NV Memory Failure

4.

Coil Drive Open Circuit Failure

Table 4-1. WRITE_LOCK Parameter

FEATURE_SEL
HW_SEL bit

FEATURE_SEL
SW_SEL bit

SECURITY SWITCH

WRITE_LOCK

WRITE_LOCK
Read/Write

DEFINE_WRITE_LOCK

Write access
to blocks

0 (off)

0 (off)

NA

1 (unlocked)

Read only

NA

All

0 (off)

1 (on)

NA

1 (unlocked)

Read/Write

NA

All

0 (off)

1 (on)

NA

2 (locked)

Read/Write

Physical

Function
Blocks only

0 (off)

1 (on)

NA

2 (locked)

Read/Write

Everything

None

1 (on)

0 (off)

(1)

0 (unlocked)

1 (unlocked)

Read only

NA

All

1 (on)

0 (off)

1 (locked)

2 (locked)

Read only

Physical

Function
Blocks only

1 (on)

0 (off)

1 (locked)

2 (locked)

Read only

Everything

None

(1) The hardware and software write lock select bits are mutually exclusive and the hardware select has the highest priority. When the HW_SEL bit if set to 1

(on), the SW_SEL bit is automatically set to 0 (off) and is read only.

«
...
46
47
48
49
50
...
»

Summary of Contents for 8700 Series









































































































































Reviews:

No comments

Related manuals for 8700 Series

Brand: Kawai Pages: 33

Brand: Kawai Pages: 60

Brand: 4iiii Pages: 3

Brand: Tactical Controls Pages: 11

Brand: FarmChem Pages: 8

Brand: Kathrein Pages: 10

Brand: Veeder-Root Pages: 59

Brand: Hanna Instruments Pages: 9

Brand: FMS Pages: 12

Brand: Omega Pages: 20

Brand: Vaisala Pages: 11

Brand: NARDA Pages: 14

Brand: Stabila Pages: 14

HydroTracer FLV HT2

Brand: aboni Pages: 48

Brand: East Tester Pages: 36

Brand: Chauvin Arnoux Pages: 12

Brand: AlazarTech Pages: 60

Brand: Kobold Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands