Emerson 8700 Series Reference Manual Download Page 25 | Manualshive

Page: 25 / 136

background image

Reference Manual

00809-0100-4793, Rev CA
August 2004

3-3

Rosemount 8742C

FLOWTUBE HANDLING

Handle all parts carefully to prevent damage. Whenever possible, transport
the system to the installation site in the original shipping containers.
Teflon

®

-lined flowtubes are shipped with end covers that protect it from both

mechanical damage and normal unrestrained distortion. Remove the end
covers just before installation.

Flanged 6- through 36-inch flowtubes come with a lifting lug on each flange.
The lifting lugs make the flowtube easier to handle when it is transported and
lowered into place at the installation site.

Flanged ½- to 4-inch flowtubes do not have lugs. They must be supported
with a lifting sling on each side of the housing.

Figure 3-1 shows flowtubes correctly supported for handling and installation.
Notice the plywood end pieces are still in place to protect the flowtube liner
during transportation.

Figure 3-1. Rosemount 8705
Flowtube Support for Handling

See ”Safety Messages” on pages 3-1 and 3-2 for complete warning information.

½- through 4-Inch

Flowtubes

6-Inch and Larger

Flowtubes

8732-0281B02AB, C02AB

«
...
23
24
25
26
27
...
»

Summary of Contents for 8700 Series









































































































































Reviews:

No comments

Related manuals for 8700 Series

Brand: 3M Pages: 2

Brand: 3M Pages: 16

Brand: Danfoss Pages: 6

Brand: Waltron Pages: 11

Brand: Labom Pages: 6

Brand: Labom Pages: 5

SourceMeter 2400

Brand: Keithley Pages: 594

System SourceMeter 2601B

Brand: Keithley Pages: 864

Brand: Labgear Pages: 8

SourceMeter 2600B Series

Brand: Keithley Pages: 897

Brand: MadMan Pages: 37

Brand: MADDALENA Pages: 5

Brand: Keithley Pages: 44

Brand: Keithley Pages: 76

Brand: Keithley Pages: 12

Brand: Keithley Pages: 281

Brand: Orange Electronic Pages: 21

Brand: Bontempi Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands