Emerson 189192G3 Design Manual Download Page 53

Page: 53 / 84

Liebert XD Cooling Modules—Liebert XDO, Liebert XDV, Liebert XDH and Liebert XDCF

4.9

Liebert XD Piping Dimensions and Features

4.9.1 Piping Installation Method prefabricated headers

The assembly and connection means used for piping in the Liebert XD system are similar to those

used for conventional refrigeration systems. All piping should be installed with high-temperature

brazed joints. Soft solder is not recommended. During brazing, the lines must be filled with flowing

dry nitrogen to prevent excessive oxidation and scale formation inside the piping. Prevailing good

refrigeration practices must be employed for piping supports, leak testing, dehydration and charging.

Failure to use good system practices may result in damage to the system. Refer to the ASHRAE

refrigeration handbook for general good-practice refrigeration piping.
Follow all guidelines in

3.13 - Liebert XD Piping System Design

and

3.14 - Liebert XD Piping

Slope

during installation.

Figure 46 Two-port prefabricated piping for Liebert XD cooling modules

Table 18

Two-port prefabricated piping legend

Branch Piping

Standard Run

Long Run *

Two Port

185797G21

185800G21

Supply

inch (mm)

Outside Diameter (ODS)

1-1/8

1-3/8

Height (H)

8-3/4 (222)

Length (L)

6-3/4 (171)

6-7/8 (175)

Return

inch (mm)

Outside Diameter (ODR)

2-1/8

2-5/8

Height (H)

10-1/2 (267)

Length (L)

8-3/4 (222)

9-1/8 (232)

* Pipe runs greater than 60 equivalent feet

DPN000773
Page 1, Rev. 3

Return

Supply

Nominal

96"

(2438mm)

ODS

ODR

Ref. Typ.

Ref.
Typ.

48"

(1219mm) Ref. Typ.

8-5/16"

(211mm)

24"

(610mm)

Summary of Contents for 189192G3





















































































Search results

Summary of Contents for 189192G3

Reviews:

Related manuals for 189192G3

Brands by name

Popular brands

Emerson 189192G3, Design Manual

Search results

Summary of Contents for 189192G3

Reviews:

Related manuals for 189192G3

Brands by name

Popular brands