Emerson Quiet Kool 19 SEER Series Owner'S Manual Download Page 4

1

During  the installation of the indoor and outd-
oor units the access to the working area should 
be forbidden to children.
Unforeseeable accidents could happen.

Make sure that  the base of  the outdoor unit  is
firmly fixed.

Check that air  cannot enter the refrigerant sys- 
tem and check for  refrigerant leaks when  mo-
ving the air conditioner. 

SAFETY RULES AND RECOMMENDATIONS FOR THE INSTALLER 

Carry out a test cycle after installing the air co-
nditioner and record the operating data. 

The user must  protect  the  indoor unit  with a 
fuse of  suitable capacity for the maximum  in-
put current or with another overload protection
device. 

Ensure that  the mains voltage corresponds  to 
that stamped on the rating plate . Keep the sw-
itch or power plug clean. Insert the power plug 
correctly and firmly into the socket, thereby a- 
voiding the risk of electric shock or fire due to 
insufficient contact. 

Check that the socket  is suitable for the plug , 
otherwise have the socket changed. 

Do not install the appliance at  a  distance  of 
less than 20

 from inflammable substances 

(alcohol, etc.) or from pressurised containers 
(e.g. spray cans). 

If  the appliance  is used  in areas without the 
possibility of ventilation, precautions must be 
taken to prevent any leaks  of refrigerant  gas
from remaining in the environment and creat-
ing a danger of fire 

The packaging materials  are  recyclable  and 
should  be  disposed  of  in the separate waste 
bins .Take the air conditioner at the end of  its 
life to 

 waste collection center 

for disposal. 

an authorized

Only use the air conditioner  as  instructed  in 
this booklet . These instructions are not inten-
ded  to cover  every  possible  condition  and 
situation . As  with  any electrical  household 
appliance ,  common  sense  and  caution  are 
therefore  always  recommended for installat-
ion, operation andmaintenance. 

The appliance must be installed in accordance
with applicable national regulations. 

Before accessing the terminals , all the  power 
circuits must be disconnected from the  power 
supply. 

Read this guide before installing and using  the
appliance.

The appliance must be fitted with means for 
disconnection from the supply mains having 
a contact separation in all poles that provide 
full disconnection under overvoltage 
category III conditions, and these means 
must be incorporated in the fixed wiring in 
accordance with the wiring rules. 

Installation must be preformed in accorda-
nce with the requirements of NEC and CEC 
by authorized personnel only.

This appliance can be used by children a-
ged  from  8  years and above and persons 
with reduced physical, sensory or mental 
capabilities or lack of experience and kn-
owledge if they have been given supervis-
ion or instruction concerning use of the a-
ppliance in a safe way and understand the 
hazards involved. Children shall not play 
with the appliance. Cleaning and user ma-
intenance  shall  not  be made  by children 
without supervision.

The air conditioner must be installed by 
professional or qualified persons.

Summary of Contents for 19 SEER Series

































Reviews: