EMC2 VNX VG2 Hardware Information Manual Download Page 25

Page: 25 / 43

EMC VNX VG2/VG8 Hardware Information Guide

Component description

Since the 1U Control Station and the management module have the same type of RJ-45
NIC ports,

“Control Station Ethernet (RJ-45) NIC ports” on page 18

and

“Control Station

Ethernet (RJ-45) port and connector (adapter)” on page 19

provides detailed information

about the management module NIC ports, connector, and adapter.

Management module LEDs

Figure 19

shows the LEDs and

Table 11

describes them.

Figure 19 Management module LEDs

Port 2 (Link LED)

Port 0 (Link LED)

Numeric display

(blade enclosure ID)

Port 1 (Activity LED)

Power/Fault LED

Port 0 (Activity LED)

Port 2 (Activity LED)

Port 1 (Link LED)

CNS-001671

Table 11 Management module LEDs

LED

Color

State

Description

Power/Fault

Green

Management module is powered up.

Amber

Management module has faulted.

Note: LED is always illuminated at powerup, until it is
initialized.

—

Off

Management module is powered down.

Link (each

port has one)

Green

Network connection

—

Off

No network connection

Activity (each

port has one)

Amber

Blinking

Transmit/receive activity

—

Off

No network activity

numeric

(7-segment)

display for

enclosure ID

—

Displays the enclosure ID assigned to the Data Mover

enclosure.

Note: Each enclosure is assigned a number at installation.

Summary of Contents for VNX VG2












































Search results

Summary of Contents for VNX VG2

Reviews:

Related manuals for VNX VG2

Brands by name

Popular brands

EMC2 VNX VG2, Hardware Information Manual

Search results

Summary of Contents for VNX VG2

Reviews:

Related manuals for VNX VG2

Brands by name

Popular brands