manualshive.com logo in svg

Embassy ONEX, Installation And Maintenance Instructions Manual

Share
Download
Embassy ONEX Installation And Maintenance Instructions Manual Download Page 8

8

2 - GENERAL INFORMATION

2.1 - Introduction

Congratulations!
You have effectively purchased
one of the best boilers on the
market.
Each single part is built, tested and
assembled, with pride, at the
COSMOGAS factories, thereby
guaranteeing optimum quality
control.
Thanks to on-going research
carried out by COSMOGAS, this
product has been conceived and is
considered to be the best in its
class with regards to respect for
the environment.  Great
importance is also given to the end
of the boiler’s useful life. All of its
components can easily be
separated into similar and
completely recyclable parts.

2.2 - Manufacturer

COSMOGAS srl
Via L. da Vinci 16
47014 - Meldola (FC)
ITALY

Tel. +39 0543 498383
Fax. +39 0543 498393
www.cosmogas.com
[email protected]

Spare parts are available from your
local authorized wholesale distributor.
For a location of the one nearest you
call 413 -564- 9538.

45

AN

 = heating only version, for inside installation

WN

 = combi version (space heating and instantaneous D.H.W.

production), for inside installation.

AE

 = heating only version, for outdoor installation

WE

 = combi version (space heating and instantaneous D.H.W.

production), for outdoor installation.

Modulating gas-fired, condensing hot water boiler, with sealed
combustion chamber and pre-mix burner, with maximum power input
of 160,000 Btu/hr (47 kW) and minimum of 30,000 Btu/hr (9 kW)

XX

2.3 - Key to
symbols used

WARNING!!! Failure to follow these
indications can causing an
explosion, extensive property
damage, severe personal injury or
death!

 CAUTION!!!

Electrical caution! Risk of electric
shock: failure to observe this warning
may compromise the smooth running
of the appliance or cause serious
damage to individuals, animals or
property.

 

CAUTION!!!

General caution. Failure to observe this
warning may compromise the smooth
running of the appliance or cause
serious damage to individuals, animals
or property.

 

Operation symbol

 

Important indication symbol

2.4 - Description of
models

Summary of Contents for ONEX

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands