manualshive.com logo in svg

Embassy ONEX, Installation And Maintenance Instructions Manual

Share
Download
Embassy ONEX Installation And Maintenance Instructions Manual Download Page 2

2

SAFETY INSTRUCTIONS

- Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do
not use any phone in your building.

•

Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.

•

If you cannot reach your gas supplier,
call the fire department.

- Installation and service must be

performed by a qualified installer, service
agency or the gas supplier.

- Ne pas entreposer ni utiliser d’essence ou

ni d’autres vapeurs ou liquides
inflammables à proximité de cette appareil
ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE

ODEUR DE GAZ:

•

Ne pas tenter d’allumer l’appareil.

•

Ne touchez à aucun interrupteur, ne
pas vous servir des téléphones se
trouvant dans le bâtiment

•

Appelez immédiatement votre
fournisseur de gas de puis un voisin.
Suivez les instructions du fournisseur.

•

Si vous ne pouvez rejoindre le
fournisseur, appelez le service des
incendies

- L’installation et l’entretien doivent être

assurés par un installateur ou un service
d’entretien qualifié ou par le fournisseur
de gaz.

WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury or death.

AVERTISSMENT: Assurez vous de bien
suivre les instructions données dans
cette notice pour réduire au minimum le
risque d’incendie ou d’explosion ou pour
éviter tout dommage matériel, toute
blessure ou la mort

Summary of Contents for ONEX

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands