manualshive.com logo in svg

EM Acoustics EMS-122, User Manual

Share
Download
EM Acoustics EMS-122 User Manual Download Page 2

2

 

EMS-122/122w User Manual 

www.emacoustics.co.uk 

CONTENTS 

 
Introduction  

 

Thank you ...……………………………………………………………………………………………………………………………. 3 

 

Unpacking ……………………………………………………………………………………..……………………………………….. 3 

 

Declaration of Conformity …………………….…………………………………………………………………………………… 3 

 
Product Overview 

 

EMS-122 passive two-way enclosure ..............…………………………………………………………………….……… 4 

 

EMS-122w wide dispersion passive two-way enclosure ..……………………………………………………….……… 4 

 

 

System Set-up 

 

Safety Considerations………………………………………………………………………………………………………………… 5 

 

Cabling & Amplifier selection ……………………………………………………………………………………………………… 6 

 

Protective DSP Settings ................................................................................................................. 7 

 

Mounting & Rigging Options 

 

Rigging Hardware & Accessories ………………………………………………………………………………………………… 8 

Permanent Installations …………………………………………………………………………………………………………….. 8 

 

Flying hardware Use........……………………………….…………………………………………………………………………. 9 

 

Omnimount/Powerdrive Installation hardware use .......................................................................... 10 

 

Maintenance 
 

EMS-122 Drive Unit Service ……………………………………………………………………………………………………….11 

 

 

Warranty ……………………………………………………………………………………………………………………………………………. 12 

 

Appendix A – Technical Specifications …………………………………………………………………………………………………… 13 

Summary of Contents for EMS-122














Reviews:

No comments

Brands by name

Popular brands

Load more brands