background image

12

 

EMS-122/122w User Manual 

www.emacoustics.co.uk 

WARRANTY 

 

Limited Warranty 
 

This EM Acoustics loudspeaker product is warranted to the original end-user purchaser and all subsequent owners 

for a period of 

three years

 from the original date of purchase. 

 

Warranty Coverage 

 

This warranty covers defects in materials and workmanship.  It does not include: 

 

Damage  or  failure  caused  by  accident,  misuse,  neglect,  abuse  or  modification  by  any  person  other  than  an 
authorised EM Acoustics representative. 

 

Damage or failure caused by operating the loudspeaker product contrary to the instructions contained within 
this manual. 

 

Damage caused during shipment. 

 

Claims based on any misrepresentation by the seller. 

 

Products which contain anything other than the original components (or EM Acoustics factory supplied spare 
parts). 

 

Products on which the serial number has been removed, altered or defaced. 

 

Returning your EM Acoustics loudspeaker 

 

Should your EM Acoustics loudspeaker develop a fault, please return it (freight prepaid) in its original packaging, 
along with proof of purchase to your local dealer or to:  

 

EM Acoustics (Returns Department), Building 74, Dunsfold Park, Cranleigh, Surrey, GU6 8TB, UK 

 

including a description of the suspected fault.  Serial numbers must be quoted in all correspondence relating to the 

claim.  EM Acoustics or its representatives are in no way liable for any loss or damage in transit, and hence it is 

recommended that the sender insure the shipment.  EM Acoustics will pay for return freight should the repair be 

covered under warranty. 
 

EM Acoustics’ liability is to the replacement or repair (at our discretion) of any defective components, and as such 

are  not  liable  for  any  incidental  and  consequential  damages  including  (without  limitation)  injury  to  persons, 

damage to property or loss of use. 

 

This  warranty  is  exclusive  and  no  other  warranty  is  expressed  or  implied.    This  warranty  is  also  in 

addition to – and in no way detracts from – your statutory rights as a consumer. 

Summary of Contents for EMS-122














Reviews: