elysator PUROTAP compenso 12 Operating Instructions Manual Download Page 10

10

corresponds to approx. 20 µS/cm or 1 °dH corresponds to approx. 35 µS/cm. 

 

Sequence of units: µS/cm -- °C | µS/cm -- °F | TDS -- °C | TDS -- °F

ON/OFF key (MANU/AUTO)

Press the   key once to switch on the combined meter. The water quality is 

measured for 10 seconds and compared to the set limit. During measuring, 

the background is lit in blue and the conductivity value is displayed. If the 

measured value is below the set limit, everything is OK. If the measured value 

exceeds the limit, the display flashes red, an alarm signal sounds and the 

floating contact switches over (only when using the optional power supply 

unit). The present throughput and the water temperature, as well as the total 

amount of water throughput, are continuously displayed. Press the key for 

approx. 3 seconds to switch off the device. If the combined meter is switched 

on and measures no throughput for about one hour, it automatically switches 

off. During operation with the optional power supply unit, the combined 

meter does not automatically switch off and cannot be switched off manually. 

If the combined meter has switched off automatically, it will automatically 

restart once throughput (> 2 l/min) resumes. If the combined meter is 

switched off using the ON/OFF key, it will not restart automatically. 

Auto mode

Press the   key

 

twice in quick succession to start automatic monitoring by 

the combined meter. The 

 symbol appears to indicate that monitoring has 

been enabled. In auto mode, the meter only takes measurements when 

water is actually passing over it. If the throughput is interrupted, the meter 

continues to show the last captured value. When a throughput is present, the 

meter takes a new reading of the conductivity value after every 10 litres and 

displays it. If the limit is exceeded in two successive measurements, the 

display continuously flashes red and an acoustic alarm sounds. In addition, 

the floating contact is switched over. If the   key is pressed for a third time, 

the meter exits auto mode. Auto mode is recommended for operation with 

an automatic topping up device.

Summary of Contents for PUROTAP compenso 12
















Reviews: