manualshive.com logo in svg

ELSYS.se LoRaWAN ERS Desk, Operating Manual, Page: 5 / 18

Share
Download
ELSYS.se LoRaWAN ERS Desk Operating Manual Download Page 5

 

5 

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden 
E-mail: 

[email protected]

 

ǀ

 Web: 

www.elsys.se

 

Main features of ERS Desk 
 

•

 

Compatible with LoRaWAN® specification 1.0.3 

•

 

Detects occupancy with an infrared temperature sensor 

•

 

Detects motion using a passive IR sensor 

•

 

Can detect occupancy even if people are sitting/standing still 

•

 

Measures ambient temperature 

•

 

Measures ambient humidity 

•

 

Measures light intensity 

•

 

Easy installation 

 

•

 

Easy configuration 

•

 

May be installed under a desk or any surface 

•

 

Battery-powered 

•

 

Long-range communication 

•

 

Configurable over NFC 

•

 

Configurable over the air 

•

 

Ten years of battery life* 

•

 

Supported channel plans: US902-928, EU863-870, AS923, AU915-
928, KR920-923, RU864, IN865 & HK923 

•

 

CE Approved and RoHS compliant 

 

 

 

 

*Depending on settings and environmental factors

Summary of Contents for LoRaWAN ERS Desk



















Reviews:

No comments