Elspec G3500 BlackBox User And Installation Manual Download Page 257

Page: 257 / 358

257

About Advanced Settings

Within the

Advanced Tab

you may configure the Portable BLACKBOX device series' unique

capabilities. These capabilities include:



View & Copy the System Log



Configure your GPS



Create Custom Events



Configure & Send E-Mail Alerts



Produce Energy & Parameter Logs for Reporting



Configure the Energy Meter



Customize Display in Display Setup



Upgrade your G3500/G4500's Software

OPEN THE ADVANCED TAB



Access

the Portable BLACKBOX unit via

Elspec's Web Interface

log on as the

Administrator

select the

Configuration Tab



All the advanced settings are located under the

Advanced Tab:

Summary of Contents for G3500 BlackBox







































































































































































































































































































































































Search results

Summary of Contents for G3500 BlackBox

Reviews:

Related manuals for G3500 BlackBox

Brands by name

Popular brands

Elspec G3500 BlackBox, User And Installation Manual

Search results

Summary of Contents for G3500 BlackBox

Reviews:

Related manuals for G3500 BlackBox

Brands by name

Popular brands