manualshive.com logo in svg

elsner elektronik Suntracer KNX basic, Installation And Adjustment

Share
Download
elsner elektronik Suntracer KNX basic Installation And Adjustment Download Page 7

 

6 

1 

Cable connection to the rain sensor in the housing cover 

2 

Opening for the cable for the voltage supply 

3 

Tension clamp for voltage supply (230 V AC),  

suitable for massive conductors of up to 1.5 mm² or conductors with fine wires 

4 

Opening for bus cable 

5 

Slot for KNX clamp +/- 

6 

Programming pushbutton for the teach-in of the device 

7 Programming 

LED 

8 

Adjusting screw DCF77 antenna 

9 

Control LED DCF77 reception 

 

24 V DC version 

Fig. 2 

 

1 

Slot for cable connection to the rain sensor in the housing cover 

2 

Tension clamp for voltage supply (24 V DC/20 V AC),  

suitable for massive conductors of up to 1.5 mm² or conductors with fine wires 

3 

Opening for the cable for the voltage supply 

4 

Opening for bus cable 

5 

Slot for KNX clamp +/- 

6 

Programming pushbutton for the teach-in of the device 

7 Programming 

LED 

8 

Adjusting screw DCF77 antenna 

9 

Control LED DCF77 reception 

 

Summary of Contents for Suntracer KNX basic



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands