elsner elektronik Suntracer KNX basic Installation And Adjustment Download

Page: 41 / 50

Weekly watch Mon, Tue, Wed, Thu, Fri, Sat, Sun 1 … 4

Setting of switching times by

Parameter • Communication objects

Activation-time
hours

0 … 23

Activation-time
minutes

0 … 59

Switch-off time

hours

0 … 23

Switch-off time

minutes

0 … 59

Shall sequence 1 / 2 / 3 / 4 be allocated to the

linkage weekly watch OR 1 / 2 / 3 / 4?

do not allocate • allocate

Communication object

switching output Monday 1 / 2 / 3 / 4

(as in case of switching output night)

Note: If for example the set switch-off time is 3.35 pm, the output switches off when the

time changes from 3.35 pm to 3.36 pm.

Use of the week time switch:

Communication object „Week time switch OR 1/2/3/4“

The sequence 1 swichting times of all weekdays are combined via the OR logic gate

“Sequence 1” and can be used as communiction object “Week time switch 1” for own

logic links .

Summary of Contents for Suntracer KNX basic



















































Search results

Summary of Contents for Suntracer KNX basic

Reviews:

Related manuals for Suntracer KNX basic

Brands by name

Popular brands

elsner elektronik Suntracer KNX basic, Installation And Adjustment

Search results

Summary of Contents for Suntracer KNX basic

Reviews:

Related manuals for Suntracer KNX basic

Brands by name

Popular brands