Sensor KNX VOC/TH-UP Touch CH
2
Sensor KNX VOC/TH-UP Touch CH
• Version: 30.11.2021 • Technical changes and errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de •
Technical Service: +49 (0) 7033 / 30945-250
Basically the display can show a two-row or three-row text (e. g. for measured va-
lues) or a temperature controller. You can switch between the two types by pres-
sing one of the buttons, if this has not been disabled in the ETS.
5.1. Mode display and manual temperature controller
Depending on the ETS setting selected, the mode display will only display show
the current target value, or the base target value setting with scale display. The ma-
nually adjustable range can be set in the ETS.
The following display options are available:
Symbols
Priority (points)
One point: Priority 1/priority control. It is not possible to adjust the temperature au-
tomation system manually. Neither the target temperature nor the operating mo-
des can be changed using the buttons on the unit.
Two points: Priority 2. The target temperature and operating mode can be changed
using the buttons.
5.2. Change ambient temperature with the buttons
If the mode display is active, the target ambient temperature and the operating
mode can be changed manually using the buttons. The button functions can be
blocked in the ETS or be suppressed for Priority 1 operating modes. The individual
operating modes can also be locked for manual selection in the ETS.
6.
Disposal
After use, the device must be disposed of in accordance with the legal regulations.
Do not dispose of it with the household waste!
Comfort mode.
Comfort (present) target
temperature will be used.
Standby mode.
Standby (absent during day)
target temperature will be
used.
Eco mode.
Night target temperature
will be used.
Building protection mode.
Building protection target
temperature will be used.
The symbol will blink when
the mode has been activa-
ted but the activation delay
has not yet expired.
Heating mode.
Heating will be provided.
Cooling mode
Cooling will be provided.
Decrease tar-
get tempera-
ture (-)
briefly press
left button
Ambient temperature in the
current mode is decreased.
The sep-size is defined in the
ETS (0.1°C to 5°C).
Increase tar-
get tempera-
ture (+)
briefly press
right button
Ambient temperature in the
current mode is increased.
The sep-size is defined in the
ETS (0.1°C to 5°C).
Fig. 4
Mode display with current target value and/or
base target value
Fig. 5
Mode display with scale display for adjusting
the base target value.
The control position in the image reads "Base
target value reduced".
Fig. 6
Mode display with scale display and number.
Shows the set target value change.
The control position in the image reads "Base
target value reduced to 1.0°".
Fig. 7
Mode display with scale display and range.
Shows the possible adjustment range (as set in
the ETS).
The control position in the image reads "Base
target value reduced".
Fig. 8
Mode display with scale display, range and
number.
Displays the possible adjustment range (as set
in the ETS) and the set target value change.
The control position in the image reads "Base
target value reduced to 1.0°".
Fig. 9
In "HVAC mode with 2x 8 bits" control mode,
points are shown under the symbol, to indicate
the running priority of the current mode.
Change mode
press
left or right button
longer than 2 secs.
Changes between the opera-
ting modes Comfort, Standby,
Eco and Building Protection (if
deblocked in the ETS).
Extend Com-
fort mode
in Eco mode:
press both buttons
at the same time
longer than 2 secs.
Switches from Eco to Comfort
mode again for a certain time
(e. g. if the rooms are used lon-
ger in the evening).
The period is defined in the
ETS (up to 10 hours). The time
remaining in Comfort mode is
displayed.
