background image

44

Parameter setting

Sensors Intra-Sewi KNX T and Intra-Sewi KNX TH

 • Version: 11.06.2018 • Technical changes and errors excepted.

5.13. Logic

The device has 16 logic inputs, four AND and four OR logic gates.

Activate the logic inputs and assign object values up to first call.

Activate the required logic outputs.

AND logic

OR logic

Output delivers

• Maximum value
• Minimum value
• Average value

Use input 1 / 2 / 3 / 4 / 5 

No • Yes

Output sends

• on change of output
• on change of output and periodically
• when receiving an input object
• when receiving an input object and 
  periodically

Send cycle

(if sent periodically)

5 s • 10 s • 30 s • ... • 5 min • … • 2 h

At and above change of

(if sent on change)

1% • 2% • 5% • 10% • 20% • 25% • 50%

Analysis of the blocking object

• at value 1: block | at value 0: release
• at value 0: block | at value 1: release

Blocking object value 
before 1st communication

0 • 1

Behaviour of the switching output

On block

• do not send message 
• Send value 

Sent value in % 

0 ... 100

output sends on release
(with 2 seconds release delay)

• the current value
• the current value after receipt of an object

Use logic inputs

Yes • No

Object value prior to first call for:

- Logic input 1

0 • 1

- Logic input ...

0 • 1

- Logic input 16

0 • 1

AND logic 1

not active • active

AND logic ...

not active • active

AND logic 4

not active • active

OR logic 1

not active • active

Summary of Contents for Intra-Sewi KNX T





















































Reviews: