background image

 

4/14/2017 

IOMOD 16DI 

 

 

 

V1.1 | ELSETA | 

 

 

 
COPYRIGHTS AND TRADEMARKS 

 
Elseta

 

is UAB “Aedilis” trademark that identifies UAB “Aedilis” manufactured products. All of the 

products copyright belongs to "Aedilis”. These documents and the product properties can not be 
changed without company “Aedilis'” knowledge and written consent. User manual may be modified by 
company “Aedilis'” without additional notice. 

DECLARATION OF CONFORMITY 

 
(in accordance with ISO / IEC Guide 22 and EN Section 45014) 
Manufacturer: UAB Aedilis  
Address of the manufacturer L. Zamenhofo st. 5 LT Vilnius, Lithuania 
 
We claim that: 
The device IOMOD 16DI 
 
Conforms to the following standards: 
EMC: 
Radiation EN 55022 (Class A) 
1 emitted radiation (30-1000MHz) 
Second radiation conductors (0.15-30MHz) 
EN 50082-1 immunity test 
1 IEC 801-3: Radio-frequency electromagnetic field 
2 IEC 801-2: Electrostatic discharge. 
3 IEC 801-4: Quick periodic electrostatic discharges 
 
Additional information: 
"The device complies with the Low Voltage Directive 73/23 / EEC and EMC Directive 89/336 / EEC. 
Device assembly complies with the RoHS Directive. 
 
Manufacturer contact: 
Equipment quality controller 
UAB Aedilis " 
Address: L. Zamenhofo g. 5, LT 06332, Vilnius, Lithuania 
Phone: +370 5 2742707 
E-mail. Email: [email protected] 
 

 

Summary of Contents for IOMOD 16DI


















Reviews: