manualshive.com logo in svg

ELPRO 805U, User Manual

Share
Download
ELPRO 805U User Manual Download Page 53

 805U Radio Modem  Module

 User Manual

Page 

54

©

   November 2004

AT&G

Set module’s Group Address   Range 0-255. Default 0.

AT&K

Flow Control Configuration.

&K0

Flow Control Disabled. CTS Always high. Module ignores RTS.

&K1

not used

&K2

not used

&K3

CTS/RTS Flow Control. CTS Reflects the state of the local buffer. Module only
transmits serial data when RTS is high.

&K4

•

RS-485 Control. Must be selected for RS-485 to work. CTS is high. CTS goes
low when transmitting data. RTS is ignored.

AT&L

Configuration of start-up mode,  and controlled mode operation.

&L0

At power-up, the module enters command mode and waits for commands.
Normal single-connect controlled mode operation.

&L1

•

If set to transparent mode in AT&M, the module automatically goes online.  For
controlled mode, ATD automatically dials the number stored in Z0, ATA answers
an incoming call.

&L2

Auto-connect mode  -  master. The module “dials” the number stored in &Z0
automatically. It continuously attempts to connect to that number. Use DTR with
the AT&D command to control the connection.

&L3

Auto-connect mode  -  slave. The module continuously attempts to answer any
incoming call. Use DTR with the AT&D command to control the connection.

AT&M

Operating Mode. This allows selection between transparent mode and controlled
mode.

&M0

•

Transparent Mode.

&M1

Transparent Repeater. All serial data is sent out the radio, with the configured
system (AT&S) and group (AT&G) address. All incoming radio data with the
correct system address and matching group address is sent out the serial port, and
also re-transmitted out the radio port using the unit address (AT&U) setting as the
group address. All incoming radio data with the configured system address and
group address matching the Unit address is re-transmitted out the radio with the
group address set to the group address.

&M2

Controlled Mode.

&M3

Not used.

AT&N

Abort Connection Control. Controls whether the module will abort a connection
attempt in controlled mode if a character is entered.

&N0

Ignore characters entered while attempting to make a connection.

&N1

•

If a key is hit or a character input while attempting to connect, abort the
connection attempt and return to command mode.

AT&S

Set module’s System Address Range 0-255.

AT&T

Self Tests. Allows in-field diagnostics, and factory testing.

Summary of Contents for 805U


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands