2
INSTALLATION INSTRUCTIONS
1.- WARNING
•
The warranty of the heater will not cover any damage caused by non observance of any of these instructions.
•
The instructions should be retained for future reference. This guide must be kept and given to any new owner.
•
Please check that the voltage in the rating label fits the power supply.
•
Any reinstallation should be carried out by trained personnel.
•
The use of these heaters is forbidden in any area where there is a presence of gases, explosives or inflammable objects.
•
DO NOT USE THIS HEATER TO DRY CLOTHES.
•
The surfaces of this heater can be hot, so young children should not be left unsupervised in the vicinity of the heater.
•
Children should be supervised to ensure they do not play with the appliance.
•
Neither the connecting cable nor any other object must come into contact with the hot unit.
•
Do not cover this heater at any time.
•
The air outlet at the top of the thermal radiator and the air inlet at the bottom are provided to ensure the most efficient operation of the appliance.
They also protect the heater from overheating; therefore, it is essential that at no time are they covered.
•
This heater should be switched off at the isolating switch before any repair work is carried out.
•
The thermal radiator should not be installed just below an electrical socket.
•
The appliance must be installed in such a way that it is impossible for anyone using a bath or shower, to touch the controls.
•
The installation must be carried out in accordance with the current electrical regulations.
•
The heater is fitted with a flexible cable size 3 x 1.00 mm
²
for electrical connection. It may be used to connect the heater to the fixed wiring of the
premised through a suitable connection box positioned adjacent to the heater.
•
The supply circuit to the heater must incorporate a double pole isolating switch having a contact separation of at least 3 mm.
•
If the flexible power cable for this unit is damaged, it may only be replaced by a repair workshop recognised by the manufacturer, as special tools
are necessary.
•
This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
•
This appliance must be earthed.
•
The infrared heater is designed to only work in a horizontal position.
•
All models are supplied with an electrical interrupt cut-out. This will switch off the heater if, for any reason, it overheats. Should the cut-out
operate, turn the heater off and remove the cause for the overheating. The cut-out will be reset automatically.
•
The presence of air particles of smoke, dust and other pollutants could, in time, discolour the walls and surfaces around the heater.
MODELS
RX4P
RX4F
RX4E
RX6P
RX6F
RX6E
RX8P
RX8F
RX8E
RX10P
RX10F
RX10E
RX12P
RX12F
RX12E
MODULES
4
6
8
10
12
W (cm)
41.5
57.5
73.5
89.5
105.5
D (cm)
10 + 2 cm separated from the wall
H (cm)
58
WEIGHT (kg)
9,5
13,5
17,5
21,5
25,5
VOLTAGE
220-240V~
INPUT (W)
500
750
1000
1250
1500
2.- INSTRUCTIONS ON INSTALLATION
- Open the carton at the indicated side. The screws are in the accessories bag. Turn the carton upside down to allow the heater to stand. Check
that it is the correct model and that it is in good condition.
- To obtain optimum performances it is necessary to maintain a minimum clearance of 15 cm between the radiator and any inflammable material as
furniture, curtains etc. See figure.
shelf
mínimum 15cm
Closest
object to the
right end
mínimum 25cm
mínimum 10cm
Closest
object to
the left
end
minimum15cm
