manualshive.com logo in svg

ELMED Isotest II RT, Operating Manual

Share
Download
ELMED Isotest II RT Operating Manual Download Page 12

Page 12

Checklist for Insulation Tests

Checklist

for the Supervision of Insulation Tests

(to DIN 30 672) using the E

LMED

 Isotest.

1.

Test of Readiness for Operation

1.1

Battery
(Varta 5M6 6 V/6 Ah or Sonnenschein 6 V/6.5 Ah)

Has the battery state of charge been checked correctly?
This test can be performed using the ELMED battery charger (see operating
manual for the battery charger).

1.2

Meaning of the Acoustic Signals

A brief buzzer sound when the test button is pressed indicates that the tester
is ready for operation.

FAULT

Buzzer does not sound when the test button is pressed.

CAUSE

REMEDY

Main switch on tester has not been
turned on.

Turn main switch to ON or I

No battery installed in tester

Install battery

Battery discharged

Replace battery or inspect old
battery and recharge.

Fuse blown

Check fuse (VT/VRT only) and
replace, if necessary

Technical defect in the tester

Send in tester for inspection

Summary of Contents for Isotest II RT





















Reviews:

No comments

Brands by name

Popular brands

Load more brands