background image

 

 

Technical Support: 023 9269 6638 

                        

PAK200838_03A  Feb 2019                           ©2019 ELMDENE INTERNATIONAL LTD 

  

 

S

PECIFICATION

 

 

 

Sound Output 

 

 

113

 dBA @ 1m 

Frequency range    

 

~ 2430 - 3250 Hz 

Power Supply 

 

 

9.0 

 15.0Vdc, 14.3Vdc optimal charge 

Current Consumption 

 

10mA at 14.3Vdc (quiescent/battery charged)  

Battery charging 

 

~100mA when charging fully discharged batteries 

Sounding 

 

 

1.55A max from battery

 

 

  

Cut-off Timer 

 

 

Selectable 5 seconds, 90 seconds, 3 minutes, 15 minutes. 

 (5 seconds only for installation 

 not a certified duration) 

Batterie

 

 

 

12V 2.1Ah SLA - Battery recharge in less than 24 hours  
(Following 10 x 3 minute soundings) 

NOTE: The SI500 siren is specified for operation with a  
Powersonic PS-1221 battery and it is recommended to use this battery. 

Battery Low Voltage Detection 

10.9V nominally 

Battery Deep DIscharge Protection 

9.5V nominal (resulting in de-activation of sounder) 

Battery autonomy duration   

36h 

Tamper detection 

 

Cover switch 

Tamper Output   

 

Max 2A / 30Vdc rated 

Sound Trigger Input 

 

BL+ < 2.9Vdc. 

Dimension / Weight 

 

193mm H x 184mm W x 70mm D / 1.4kg without battery 

Fixings 

 

 

M5 self-tapping screws (4-off) 

Cover Material   

 

Steel 

Backplate Material 

 

Steel 

Protection level   

 

IP31 & IK08 

Operating Temperature 

 

- 10

o

C to +55

o

Storage Temperature 

 

- 10

o

C to +55

o

 

 

C

OMPLIANCE

 

 

 

This product meets the essential requirements of the following EU Directives: 

EMC :

 

 

2014/30/EU  

RoHS :

 

 

2011/65/EU    

WEEE :

 

 

2012/19/EU 

Batteries :

   

2013/56/EU 

LVD :

 

 

2014/35/EU 

 

         EN50131-4:2009

  

Security Grade 2, Environmental Class II 

         RTC50131-4:2011

 

Security Grade 2, Environmental Class II 

               

 

 

 

 

CERTIFICATION BODIES 

AFNOR Certification   

 

 

 

 

CNPP Certification 

 

Tél. : + 33 (0) 1.41.62.80 00  

 

 

 

 

Tél. :+33 (0) 2.32.53.63.63 

www.marque-nf.com

  

 

 

 

 

www.cnpp.com

 

Certification reference: NF324-H58 
Certificate No.:  3130000410 

Summary of Contents for SI500








Reviews: