Ellard Fire Door Control Panel, Product Instructions

Page: 15 / 20

DOOR CLOSED ALARM
SOUND
OFF
ON - OFF
PRESS
ONCE
PRESS
ONCE
DOOR CLOSED ALARM - VISUAL AND SOUND
·
With the shutter fully closed and the fire alarm signal still present, the
Audio Visual warning can either continue or be switched OFF
AUX 1 RELAY
AFTER CLOSE
(ON)
ON - OFF
PRESS
ONCE
ROTATE TO
CHANGE
PHOTO BEAM
OPERATION IN ALARM
(OFF)
PHOTO BEAM
ALARM DELAY
(0:00)
ROTATE TO
CHANGE
ON - OFF
0 -10 MINS
PHOTO REOPEN TIME
(0:00)
0 - 10 MINS
PHOTO BEAM
RETRIES
(0.00)
0 - 10
PHOTO BEAM PAUSE
(0.01)
0 - 30 SECS
RE-OPEN TIME
(0.00)
0 - 10 MINS
FACTORY RESET
PRESS FOR 10 SEC'S?
AUX 2
·
This relay is switched in both normal and fire condition, and will
simulate any other another relay or be activate depending on its
selected function
In Fire condition the STOP relay is disabled
PHOTO BEAM OPERATION IN ALARM
(Feature disabled in SOLENOID ONLY mode)
·
Enables a connected photocell to stop and reopen a closing door when
the beam is broken
Only Active in fire condition and when turned ON in menu
PHOTO BEAM ALARM DELAY
(Feature disabled in SOLENOID ONLY mode)
·
Should the photo beam become obstructed an
audible obstruction warning will sound after a selected time
PHOTO REOPEN TIME
(Feature disabled in SOLENOID ONLY mode)
·
Upon breaking the photo beam the door will stop and reopen
for the selected time
This is typically set for the same time as
F.Close Run time
PHOTO BEAM RETRIES
(Feature disabled in SOLENOID ONLY mode)
Should the photo beam become triggered, the shutter will stop then
reopen for the time set in
PHOTO REOPEN TIME
If the photo beam remains blocked another attempt will be made to
close the shutter, this will continue for the selected number of times
If the obstruction is removed before this count is reached, the shutter
will continue and close
If on the final attempt the photo beam remains blocked, the photo
beam will be ignored and the shutter will close as far as possible
PHOTO BEAM PAUSE
(Feature disabled in SOLENOID ONLY mode)
·
This is the delay time before the next command is carried out
after the photo beam has been broken
RE-OPEN TIME
·
Automatically reopens a closed shutter for the time
selected upon removal of all active fire signals
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
PRESS AND HOLD
FOR 10 SECS
AUX 2 RELAY
(STOP)
ROTATE TO
CHANGE
STOP, OPEN CLOSE,
MAINS FAIL
LOW BATTERY
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
PRESS
ONCE
AUX 1 (AFTER CLOSE)
·
This relay is only switched ON, upon receipt of a fire signal
With the shutter fully closed and the fire alarm signal still present,
Aux 1 can either remain ON or be switched OFF
FACTORY RESET
·
Clears all previous selected times and then restores the
unit back to factory default settings
This is done by pressing and holding the program
button for 10 seconds
PRESS AND HOLD
3 SEC TO EXIT USER PROGRAM
MODE
ROTATE TO
ADVANCE
MENU
ROTATE TO
CHANGE
ROTATE TO
ADVANCE
MENU
ROTATE TO
ADVANCE
MENU
ROTATE TO
ADVANCE
MENU
ROTATE TO
ADVANCE
MENU
ROTATE TO
ADVANCE
MENU
ROTATE TO
ADVANCE
MENU
ROTATE TO
ADVANCE
MENU
ROTATE TO
ADVANCE
MENU
ROTATE TO
CHANGE
ROTATE TO
CHANGE
ROTATE TO
CHANGE
ROTATE TO
CHANGE
ROTATE TO
CHANGE
ROTATE TO
ADVANCE
MENU
Factory Reset
*OFF **ON